Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Serial Number View: Highlight Serial Number View and press Enter. Use arrow key to select a drive, the selected drive's serial number can be viewed in the last column. The serial number is assigned by the disk drive manufacturer. English VIA Tech. VT8237 SATA RAID BIOS Ver 2.31 View the serial number of hard disk, it is useful for identify same model disks F1 : View Array/disk Status .........., ..........: Move to next item Enter : Confirm the selection ESC : Exit ..........Create Array ..........Delete Array ..........Create/Delete Spare ..........Select Boot Array ..........Serial Number View Channel Drive Name Array Name Mode Size(GB) Status Serial_Ch0 Master ST3120026AS ARRAY 0 SATA 111.79 Stripe0 Serial_Ch1 Master ST3120026AS ARRAY 0 SATA 111.79 Stripe1 Serial Number: 3JT354CP E. View Array Status: Press the F1 key to show the array status on the lower screen. If there are no disk arrays then nothing will be displayed on the screen. VIA Tech. VT8237 SATA RAID BIOS Ver 2.31 Create a RAID array with the hard disks attached to VIA RAID controller F1 : View Array/disk Status .........., ..........: Move to next item Enter : Confirm the selection ESC : Exit Array Name Array Mode Block Size(GB) Size(GB) ARRAY 0 Stripe 64K 223.58 ..........Create Array ..........Delete Array ..........Create/Delete Spare ..........Select Boot Array ..........Serial Number View -67 -Appendix English Installing the RAID drivers To install operating system onto a serial ATA hard disk successfully, you need to install the SATA controller driver during OS installation. Without the driver, the hard disk may not be recognized during the Windows setup process. First of all, copy the driver for the SATA controller from the motherboard driver CD-ROM to a floppy disk. See the instructions below about how to copy the driver in MS-DOS mode(Note1). Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk. Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from the startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\> prompt, type the following two commands. Press ENTER after each command (Fig.1): cd bootdrv menu Step 2: When the controller menu (Fig.2) appears, remove the startup disk and insert the blank formatted disk. Select the controller driver by pressing the corresponding letter from the menu. Your system will then automatically zip and transfer this driver file to the floppy disk. Press 0 to exit when finished. (Note 2) Fig.1 Fig. 2 Step 3: After completing the steps, boot from the Windows installation disk to install the RAID drivers. Press F6 as soon as you see the "Press F6 if you need to install a third party SCSI or RAID driver" message, then supply serial ATA controller driver by this floppy disk. Follow the on-screen instructions to complete the installation. (Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under Windows once for that hard drive. After that, the driver will not have to be installed.) (Note 1) For users without a startup disk. Use an alternative system and insert the GIGABYTE motherboard drive CD-ROM. From the CD-ROM drive (example: D:\) double click the MENU.exe file in the BootDrv folder. A command prompt window will open similar to that in Fig. 2. (Note 2) If you wish to install 64-bit Windows Operating System, select F) 8237-XP64. GA-8VM800M Motherboard - 68 English 4-1-5 2 / 4 / 6 Channel Audio Function Introduction 2 Channel Audio Setup We recommend that you use speakers with amplifier to get the best sound effect if the stereo output is applied. STEP 1: Connect the stereo speakers or earphone to "Line Out." Line Out STEP 2: After installing the audio driver, you'll find a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function. STEP 3: On the AC97 Audio Configuration menu, click the Speaker Configuration tab and select the 2-channel mode for stereo speaker output check box. -69 -Appendix English 4 Channel Analog Audio Output Mode STEP 1: Connect the front channels to "Line Out," the rear channels to "Line In." Line In Line Out STEP 3: On the AC97 Audio Configuration menu, click the Speaker Configuration tab and select the 4-chan- nel mode for 4 speaker output check box. Clear the Only SURROUND-KIT check box and press OK. STEP 2: After installing the audio driver, you'll find a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function. When the Environment setting is None, the sound would be performed as stereo mode (2-channel output). Please select other settings (ex: Living Room) for 4-channel output. GA-8VM800M Motherboard - 70 Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module. STEP 1: Connect the front channels to "Line Out",the rear channels to "Line In", and the Center/Subwoofer chan- Line In nels to "MIC In". M...