Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
SATA Mode Selection IDE Determine IDE as the SATA mode. (Default setting) RAID Enable the SATA RAID function. ACHI Set this item to enable SATA AHCI function for WinXP-SP1+IAA driver supports AHCI mode. SATA Port 0/1/2/3/4/5 The category identifies the types of Serial SATA hard disk from drive 0 to 5 that has been installed in the computer. System will automatically detect HDD type. 38 GA-6FXSV Motherboard Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Hard drive information should be labeled on the outside device casing. Enter the appropriate option based on this information. TYPE 1-39: Predefined types. Users: Set parameters by User. Auto: Set parameters automatically. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. ATAPI Removable: Removable disk drive is installed here. Multi-Sector Transfer This field displays the information of Multi-Sector Transfer Mode. Disabled: The data transfer from and to the device occurs one sector at a time. Auto: The data transfer from and to the device occurs multiple sectors at a time if the device supports it. LBA Mode This field shows if the device type in the specific IDE channel support LBA Mode. 32-Bit I/O Enable this function to maximize the IDE data transfer rate. Transfer Mode This field shows the information of Transfer Mode. Ultra DMA Mode This filed displays the DMA mode of the device in the specific IDE channel. 39 GA-6FXSV Motherboard Peripheral Configuration Figure 2-6: Peripheral Configuration Serial Port A This allows users to configure serial port A by using this option. Enabled Enable the configuration. (Default setting) Disabled Disable the configuration. Base I/O Address 3F8 Set IO address to 3F8.(Default setting) 2F8 Set IO address to 2F8. 3E8 Set IO address to 3E8. 2E8 Set IO address to 2E8. 40 GA-6FXSV Motherboard Serial Port B This allows users to configure serial port B by using this option. Enabled Enable the configuration (Default setting) Disabled Disable the configuration. Base I/O Address 3F8 Set IO address to 3F8. 2F8 Set IO address to 2F8. (Default setting) 3E8 Set IO address to 3E8. 2E8 Set IO address to 2E8. 41 GA-6FXSV Motherboard Boot Device Configuration Figure 2-7: Boot Device Configuration Boot -time Diagnostic When this item is enabled, system will shows Diagnostic status when system boot. Enabled Enable Boot-time Diagnostic. Disabled Disable this function. (Default setting) Post Error Pause The category determines whether the computer will stop if an error is detected during power up. All Error Whenever the BIOS detects a non-fatal error the system will be stopped. No Error The system boot will not stop for any error that may be detected and you will be prompted. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default setting) 42 GA-6FXSV Motherboard NumLock This option allows user to select power-on state for NumLock. On Enable NumLock. (Default setting) Off Disable this function. 43 GA-6FXSV Motherboard Thermal and Acoustic Configuration Figure 2-8: Thermal and Acoustic Configuration 44 GA-6FXSV Motherboard Open loop Thermal Throttle Enabled Open loop Thermal Throttle. (Default setting) Disabled Disable Open loop Thermal Throttle. Temperature Chassis inlet This item is user defined. Use nuber key to adjust desired value. Temperature Rise This item is user defined. Use nuber key to adjust desired value. Air speed to the DIMMs This item is user defined. Use nuber key to adjust desired value. System Altitude This item is user defined. Use nuber key to adjust desired value. Pitch between DIMMs This item is user defined. Use nuber key to adjust desired value. Close loop Thermal Throttle Enabled Close loop Thermal Throttle. (Default setting) Disabled Disable Close loop Thermal Throttle. Temperature Hysteresis This item is user defined. Use nuber key to adjust desired value. Temperature Guardband This item is user defined. Use nuber key to adjust desired value. Temperature Chassis inlet This item is user defined. Use nuber key to adjust desired value. Temperature Rise This item is user defined. Use nuber key to adjust desired value. Air speed to the DIMMs This item is user defined. Use nuber key to adjust desired value. System Altitude This item is user defined. Use nuber key to adjust desired value. 45 GA-6FXSV Motherboard Pitch between DIMMs This item is user defined. Use nuber key to adjust desired value. FAN Speed Contyrol Enabled Enable FAN Speed Control. (Default setting) Disabled Disable FAN Speed Control. 46 GA-6FXSV Motherboard Power Figure 3: Power Power On by RTC Alarm You can set item to Enabled and key in Date/Time to power on system. On Enable alarm function to POWER ON system. (Default setting) Off Disable this function. (Default setting) If Resume On Time is set to On status: RTC...