Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Options available: Add-On/Onboard. Default setting is Add-On. Onboard LAN1 Controller When enabled, the system will enable the onboard LAN devices. Options available: enabled/Disabled. Default setting is Enabled. Onboard LAN1 I/O ROM Select whether to enable the selected onboard LAN device. When enabled, device expansion ROM will be initialized. Options available: enabled/Disabled. Default setting is Disabled. Onboard LAN1 I/O ROM Option Select whether to enable the selected onboard LAN device. When enabled, device expansion ROM will be initialized. Options available: PXE/iSCSI. Default setting is PXE. PCI ROM Priority In case of multiple Option ROMs (Legacy and EFI Compatible) specifies what PCI option ROM to launch. Options available: Legacy ROM/EFI Compatible ROM. Default setting is EFI Compatible ROM. 2-2-7 USB Configuration Detected USB Devices Displays the information of installed USB devices in the system. USB Controller When enabled, the USB controller will function normally. Options available: Enabled/Disabled. Default setting is Enabled. Legacy USB Support Enables or disables support for legacy USB devices. Options available: Enabled/Disabled. Default setting is Enabled. Port 60/64 Emulation Enable I/O port 60h/64h emulation support. This should be enabled for the complete USB Keyboard Legacy support for non-USB aware OS. Options available: Enabled/Disabled. Default setting is Disabled. Mass Storage Reset Timeout Define USB Mass Storage Device Start Unit command timeout. Options available: 10 sec/20sec/30sec/40sec. 2-2-8 Legacy Device Configuration Serial Port 1/2 When enabled allows you to configure the serial port settings. When set to Disabled, displays no configuration for the serial port. Options available: Enabled/Disabled. Default setting is Enabled. Device Settings Displays Serial Port 1/2 device setting information. Change Settings Change Serial Port 1/2 device settings. When set to Auto allows the server’s BIOS or OS to select a configuration. Options available: Auto/IO=3F8; IRQ=4/IO=3F8h; IRQ=3,4,5,6,7,10,11,12/ IO=2F8h; IRQ=3,4,5,6,7,10,11,12 /IO=3E8h; IRQ=3,4,5,6,7,10,11,12/IO=2E8h; IRQ=3,4,5,6,7,10,11,12. 2-2-9 Power Configuration Deep Power Off Mode Enable or Disable Deep Power Off Mode. Options available: Enabled/Disabled. Default setting is Enabled. Power On by RTC Alarm Select whether to wake up the system when an RTC alarm is detected. Options available: Enabled/Disabled. Default setting is Disabled. Restore on AC Power Loss Defines the power state to resume to after a sys-tem shutdown that is due to an interruption in AC power. When set to Last State, the system will return to the active power state prior to shutdown. When set to Stay Off, the system remains off after power shutdown. Options available: Last State/Stay Off/Power On. Default setting is Last State. 2-2-10 Console Redirection Console Redirection (Note) Select whether to enable console redirection. Console redirection enables users to manage the system from a remote location. Options available: Serial Port1/Serial Port2/Disabled. Default setting is Disabled. Terminal Type Select a terminal type to be used for console redirection. Options available: VT100/VT100+/ANSI /VT-UTF8. Bits per second Select the baud rate for console redirection. Options available: 9600/19200/57600/115200. Parity A parity bit can be sent with the data bits to detect some transmission errors. Even: parity bi is 0 if the num of 1's in the data bits is even. Odd: parity bit is0if num of 1's the data bits is odd. Mark: parity bit is always 1. Space: Parity bit is always 0. Mark and Space Parity do not allow for error detection. Options available: None/Even/Odd/Mark/Space. Stop Bits Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. Options available: 1/2. Flow Control Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a 'stop' signal can be sent to stop the data flow. Once the buffers are empty, a 'start' signal can be sent to re-start the flow. Hardware flow control uses two wires to send start/stop signals. Options available: None/Hardware RTS/CTS. (Note) Advanced items prompt when this item is defined. Recorder Mode When this mode enabled, only text will be send. This is to capture Terminal data. Options available: Enabled/Disabled. Resolution 100x31 Enables or disables extended terminal resolution. Options available: Enabled/Disabled. Legacy OS Redirection Resolution On Legacy OS, the number of Rows and Columns supported redirection. Options available: 80x24/80X25. 2-2-11 Hardware Monitor Press Enter to view the Hardware Monitor screen which displays a real-time record of the CPU/system tem perature, fan speed, and voltage. Items on this window are non-configurable. Current CPU/Slot/FP Temperature Displays current bus CPU/Slot/FP temperature. C...