Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Close proximity to an electrical outlet and a TV antenna or cable connection will facilitate a neat, easy installation. Do not mount the DKP102 above a range oroven. Be sure that the location chosen will provide adequate access to the electrical connection on the rear of the unit before continuing. 2) If the location chosen has bottom edge molding it may be necessary to use the mounting spacers provided to effectively lower the DKP102 below or even with the molding. Measure the distance between the bottom and the bottom of the cabinet. For large molding choose a combination of spacers which will allow the DKP102 to be secured to the bottom of the cabinet. 3) Measure the thickness of the bottom of the cabinet or shelf and the spacers chosen. Select the shortest screw length which will secure the DKP102 to the bottom of the cabinet. 4) Cut out the template supplied and tape it in place onto the cabinet surface to be drilled. Center punch the four holes indicated on the template and remove the template. 5 ) Carefully drill four 1/8” (5MM)holes at the locations marked above. Place the screws selected through the DKP102 and then through the spacers(if required from the bottom-up). 6) Position the DKP102 and screw it in place using the selected screws. Do not over tighten. 7) Connect your TV antenna or cable system to the antenna connector on the rear of the DKP102. 8) Plug the AC adaptor into the rear of the DKP102 and then into the wall. 9) Attach the supplied AM/FM antenna to the AM/FM antenna jacks on the rear of the DKP102. 10) Route the wires safely away from heat and moisture sources and secure them in place using the self adhesive wire mounting clip provided. 3 ■^rnrnifl CAUTION To prevent heat damage, do not place heating orcooking appliances beneath this unit. Install the unit as far as possible from a source of noise. (For example refrigerator, microwave oven, flourescent lamp etc). FRONT Figure 1 4 Main Features Front Panel Controls 1 2 3 4 5 6 7 8 1. Power Indicator- Bright red when power is on. 2. Power Button - To turn the DKP102 on or off. 3. Source Button - Press this button to select from the four available sources DVD, TV , AV, Radio. 4. Auto Pro. Button - When this button is pressed, all TV channels are searched and channels that are detected with signals of sufficient levels are automatically stored in memory. 5. LCD Display Window - The LCD display shows the current time, source selected and radio station. 6. Record Button - Press this button to record uptoa2 minute message. 7. Play Button - Press this button to playback the recorded message. 8. Numeric Buttons (1-5) - Used to recall the radio presets. 9. Mic - Microphone used for message recording . 10. Message Indicator - Flashes to indicate a message is waiting. 11. Timer Button - Used to set the timerfunction and turn offthe timer buzzerwhen activated. 12. Clock Mode Button - Used to select the clock or alarm item to be set. 13. Store Button - Used to set the AM/FM presets into memory. 14. RadioTune/ClockSet - In Standby mode these buttons are used forsetting hours, minutes, and to select from 12 and 24 hour mode. - In operation mode these buttons are used for radio tuning Up and Down. 15. Radio Band / Alarm Off Button - Radio Band selector. (Between FM1, FM2 and AM) Press this button to turn off the alarm when activated. 16. Open Button - Used to unlock the shuttle housing. 17. Bass Boost Button - Used to increase the lowfrequency (Bass) response. 18. Volume Up/Down Button - Used to increase and decrease the volume level. 19. Channel Up/Down Button - Used to go to the next channel Up or Down. 20. Sensor Cover-Allows the remote control to operate the DKP102 and the installed shuttle (DT102, DT85, DT7). 5 Main Features Back Panel Controls 1 2 3 3 3 4 5 -JH b+4-J | r^—fl—OHZHD- ' 1. TV ANT - Connect the coaxial cable from an antenna or cable TV system to this jack. 2. DC 12V- Connect the supplied AC to DC adapter to this jack. The shuttle is designed for negative ground 12V DC operation. 3. AV IN - The DKP102 will accept an AV input through the AV jacks located on the rear of the unit. The video device could be a video game system, video camera, or other input device. •VIDEOIN-Yellow •AUDIO IN (L (-White •AUDIO IN (R) - Red. 4. FM ANT - Connect the FM radio antenna to this jack. 5. AM ANT - Connect the AM radio antenna to this jack. 6 Remote Control Operation BATTERY COVER Batterv Installation Before attempting to operate your Remote Control, install the batteries as described below. 1)Turn the Remote Control face down. Using a fingernail, lift the battery cover off. 2) Install two “AAA” batteries. Make sure that proper polarity (+ or -) is observed. 3) Align the cover tabs with the remote control and press down until the coverclicks. The remote control will operate the VDS102T and Audiovox shuttle models (DT102, DT85 or DT7) It is not a universal remote control and wil...