Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
A short cord is provided to reduce the hazard of becoming entangled or tripping over a longer cord. An extension cord may be used if the electrical rating is equal to or greater than the rating of the mixer. Use an extension cord rated 10 amperes or greater. Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over. Know Your Stand Mixer Parts and Features 1. Mixer Head 2. Beater Eject Button 3. Mixer Release Button 4. Sensor Speed™ Control 5. 2-Position Turntable Features MIXER RELEASE SENSOR SPEED 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FOLD STIR COMBINE BLEND CREAM KNEAD CAKE MIX MIX COOKIESWHIP POTATOES BEATWHIP CREAMFROSTINGSEGG WHITES WITH ELECTRONIC SENSOR SPEED Sensor Speed Control The Sensor Speed Control electronically monitors the speed of the beaters and dough hooks, and automatically increases or decreases power to maintain the selected speed. Mixer Release Button The Mixer Release Button locks the Mixer Head down to ensure thorough mixing. When the Mixer Head is raised it also locks it in the upright position. Hold the Mixer Head when lowering it into the bowl. Do not press Release Button and let Mixer Head fall into bowl. Speed Guide This guide lists 14 different speed selections. The choice of speeds provides control when stirring dry ingredients or beating egg whites for a perfect meringue. Beater Eject Button This button allows finger-tip release of all attachments. Fully depress button to Cord Storage Push cord into Base of Mixer for neat storage. 2-Position Turntable The 2-Position Turntable places large or small bowls close to the attachments to minimize having to scrape the sides of the bowls. It is important to have Turntable in proper position to ensure thorough mixing, kneading, and whisking. 2 and 4 Quart Mixing Bowls Two sizes allow for a selection for the most efficient mixing, beating, or whipping. Also convenient for recipes which require two bowls. eject attachments. How to Insert Attachments Each set of attachments must be inserted into the proper hole in the Mixer Head. They are not interchangeable; there is a right and a left. Beneath the collar is etched a small R or L. This indicates the correct hole to place attachment. The “RIGHT” side of the Mixer is the side with the Sensor Speed control. The beater marked R, with Mixer Head Graphics 1. Before using, wash bowls and attachments in hot, soapy water. Rinse and dry. 2. Make sure the Mixer is turned to OFF and unplugged. 3. Place small post on bottom of Turntable in hole on Mixer Base that matches bowl to be used. 4. Press the Mixer Release button and raise the Mixer Head up. 5. The beaters and dough hooks must be inserted into specific holes in the Mixer Head. See “How to Insert Attachments.” 6. Place bowl onto Turntable. To lower Mixer Head, first raise slightly Sensor Speed™ Guide This is an illustration of the Sensor Speed Guide on your Mixer. The guide may help you select a speed for most mixing tasks. These guides are recommendations. Please adjust Mixer speed as needed. the flat bottom, should be placed in the hole on the right side of the Mixer first. Insert attachment into hole and turn slowly until tabs slip into slots in hole. Push in until attachment locks in place. Then insert the beater marked L, with the rounded bottom. If difficult to insert, turn beater one quarter turn and try again. Right Left How To Use Your Stand Mixer and press Mixer Release button to release. Lower into bowl. When lowered, the Mixer Head automati cally locks into place. 7. Plug cord into electrical outlet. Select desired speed. Prepare recipe according to instructions. 8. When finished, turn Sensor Speed Control to OFF. Unplug from outlet. 9. Press Mixer Head release button, raise Mixer Head until locked into place. 10. Press Beater Eject Button to remove attachments. SENSOR SPEED 1 FOLD 8 MIX 2 STIR 9 COOKIES 3 COMBINE 10 WHIP POTATOES 4 BLEND 11 BEAT 5 CREAM 12 WHIP CREAM 6 KNEAD 13 FROSTINGS 7 CAKE MIX 14 EGG WHITES Notes About Your Stand Mixer • The Mixer Head locks down for thorough mixing. However, there will be some “bouncing” of the Mixer Head during heavy mixing or kneading. This is caused by the flexibility designed into the Mixer. • If a spoon is accidentally caught in attachments or the motor stalls, the To Clean 1. Make sure Sensor Speed Control is turned to OFF and Mixer is unplugged. 2. Raise Mixer Head to up locked position. 3. Press Beater Eject Button to eject attachments. Recipes Check our Web site for more recipes. Mixer will automatically shut off. If this happens, turn Mixer off, then unplug. Clear obstruction. Let motor cool for 5 minutes before continuing. • Always stay near Mixer during use. The speed of turning bowls should always be monitored. 4. Bowls, beaters, and dough hooks may be washed in hot, soapy water or in automatic dishwasher. 5. Wipe Head, Base, and Turntable of Mixer with a damp cloth. Beautiful Bre...