|
Resumen del manual
2. An extension cord with the power cord must be arranged so that it will not drape over the countertop or tabletop where they can be pulled on by children or tripped over accidentally. Rev. 04/04B 1 GETTING TO KNOW YOUR CONVERTIBLE HAND/STAND MIXER Technical Specifications Voltage: 127V., 60Hz. Power: 325Watts Bowl Capacity: 3.5 Qts. 2 1. Hi-Lo Speed Selector 2. Speed Control 3. Burst of Speed Button 4. Beater Eject Button 5. Beaters 6. Stainless Steel Bowl 7. Tilt Button 8. Hand Mixer Release Button 9. Bowl Speed Control Dial 10. Hand Mixer 11. Base Stand 12. Dough Hooks 13. Spatula 14. Bowl Lid 12 14 13 OPERATING INSTRUCTIONS 1. Press the tilt button, located on the top of the support pivot . While the button is depressed, ease the support pivot back. (Fig. 4) Assembling the Hand Mixer to the Stand Warning: To avoid injury whe assembling the hand mixer to the stand, always set the speed selector on “ 0” and unplug the appliance. Support Pivot Fig. 4 Tilt Button The support pivot will lock into this raised position until it is released by pressing the tilt button again. 2. To connect the hand mixer to the support pivot, locate the two retaining prongs on the support pivot into the two rectangular holes in the heel of the hand mixer. (Fig. 5) When the hand mixer is seated on the support pivot, press down on the hand mixer to click it into place and lock the hand mixer and the support pivot together. Fig. 5 Rectangular holes Retaining prongs Support pivot Note: Ensure that the two retaining prongs on the support pivot are fully connected into the hand mixer. 3. While the hand mixer is still in the raised position, insert either the beaters or the dough hooks. 4. To lower the hand mixer, press and hold the tilt button with one hand while holding the hand mixer with the other hand and slowly lower the hand mixer down. (Fig. 6) Press the tilt button and tilt the hand mixer down Fig. 6 5. To remove the hand mixer from the pivot support, first raise the mixer by pressing the tilt button and raise the mixer up. (Fig. 7) the mixer will lock into the raised position. 6. Then press the mixer release button which is located on the under side of the pivot support with one hand and with the other lift the hand mixer by the handle upwards and away from the support pivot. (Fig. 8) Press the tilt button and tilt the hand mixer up Fig. 7 Hand mixer release button Fig. 8 4 Read all the sections of this booklet and follow all the instructions carefully. 3 OPERATING INSTRUCTIONS 1. Before using your Bravetti Convertible Hand/Stand Mixer for the first time, wash the beaters, dough hooks, bowls and spatula in warm, sudsy water. Rinse and dry thoroughly. Use a damp cloth to wash over the mixer base and the hand mixer. Dry with a soft cloth. NEVER immerse the base stand or the hand mixer in water or any other liquids. 2. Before assembling your Convertible Hand/Stand Mixer, make sure that the power cord is unplugged from the electrical outlet and that both the speed control and the base speed control dial are in the “ OFF” position. 1. Ensure that the hand mixer is not plugged in to an electrical outlet and that the speed control switch is on the “ 0” (off) position. 2. Insert the beaters into the sockets on the under side of the hand mixer and twist counter clockwise until the beater is firmly fitted into the socket. 3. To release the beaters from the unit, press on the beater eject button on the front of the unit and they will pop out. (Fig. 1) Warning: To avoid injury when inserting or removing beaters or dough hooks, always set the speed selector on “ 0” and unplug the appliance. Attaching the Beaters to the Hand Mixer 1. Ensure that the hand mixer is not plugged in to an electrical outlet and that the speed control switch is on...
Otros modelos de este manual:Mezcladoras - HAND/STAND MIXER EP586HR (280.87 kb)
Mezcladoras - HAND/STAND MIXER EP586HB (280.87 kb)
Mezcladoras - HAND/STAND MIXER EP586HL (280.87 kb)