Votos - 6, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Then screw the Nozzle Cap Nut back onto the Adapter to secure the Nozzle Gasket and Ceramic Nozzle in place. (See Figure E.) CONTROL LEVER (42C) NOZZLE CAP NUT (39C) CERAMIC NOZZLE (37C) FIGURE E NOZZLE GASKET (36C) ADAPTER (35C) SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 10 OPERATING INSTRUCTIONS 1. If possible, place the workpiece inside a sandblast cabinet. Otherwise, isolate the workpiece to make sure no damage can occur to nearby walls, tools, personal property, etc. 2. Turn the Air Supply Valve (18), Throttling Valve (18A), and Abrasive Control Valve (18B) to the “OFF” position. (See Figure F.) SAFETY VALVE (10) AIR SUPPLY VALVE (18) THROTTLING VALVE (18A) INLET CONNECTOR (19) ABRASIVE CONTROL VALVE (18B) FIGURE F 3. Connect the air compressor’s hose to the Inlet Connector (19). Then turn on the air compressor, and set its regulator between 65 to 125 PSI. Do not exceed 125 PSI. (See Figure F.) 4. Turn the Air Supply Valve (18) and Throttling Valve (18A) to the “ON” position. At this point, the Tank (1) will begin to pressurize. (See Figure F.) 5. Check for leaks at the Tank Filler Cap (12) and along all hoses and fittings as the system pressurizes. If leaks are observed, shut off the air compressor. Use the Safety Valve (10) to release any remaining air pressure within the Tank (1). Turn the Air Supply Valve (18) and Throttling Valve (18A) to the “OFF” position. Repair the leaks. Then, turn on the air compressor and resume pressurizing the Tank. (See Figure F.) 6. Grip the Blast Gun firmly with both hands. 7. Open the Abrasive Control Valve (18B). (See Figure F.) SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 11 8. Point the Blast Gun at the workpiece so that the media will strike the surface of the workpiece at about a 45 degree angle. 9. Squeeze the Control Lever (42C) of the Blast Gun to release the media. NOTE: The flow rate of the media may be irregular when the Blast Gun is first started. Provided the media is dry, the flow rate will become normal in approximately one minute. (See Figure E.) 10. Adjust the Abrasive Control Valve (18B) to increase or decrease the media flow rate. (See Figure F.) 11. Adjust the Throttling Valve (18A) to regulate the total air flow and pressure at the Blast Gun. (See Figure F.) 12. Move the Blast Gun in a circular or right to left motion until you have achieved the desired appearance (finish) on the workpiece. 13. Periodically, check the Water Trap (17) for excessive water build-up. If necessary, hold a container beneath the Water Trap and press the button located at the bottom of the Water Trap to drain the water. (See Figure D.) 14. When the sandblasting job is completed, release pressure on the Control Lever (42C) of the Blast Gun. Turn off the air compressor. Turn the Air Supply Valve (18), Throttling Valve (18A), and Abrasive Control Valve (18B) to the “OFF” position. (See Figure F.) 15. Use the Safety Valve (10) to release any remaining air pressure in the Tank (1). Check to make sure the Pressure Gauge reads “0” PSI. (See Figures D and F.) 16. Squeeze the Control Lever (42C) of the Blast Gun to release any remaining air pressure and media. (See Figure E.) 17. Disconnect the compressor air hose from the Inlet Connector (19). (See Figure F.) 18. If necessary, empty the Tank (1) of any remaining media. Then, store the Pressurized Abrasive Blaster in a clean, dry, safe location out of reach of children and other unauthorized people. INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Prior to performing any inspection, maintenance, or cleaning of the Pressurized Abrasive Blaster, turn off the air compressor. Turn the Air SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 12 Supply Valve (18), Throttling Valve (18A), and Abrasive Control Valve (18B) to the “OFF” position. Use the Safety Valve (10) to release any remaining air pressure in the Tank (1). Check to make sure the Pressure Gauge reads “0” PSI. Then, disconnect the compressor hose from the Inlet Connector (19) of the unit. 2. Before each use: Inspect the general condition of the Pressurized Abrasive Blaster and its accessories. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged air hoses, and any other condition that may affect safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Before, during, and after use: Periodically, check the Water Trap (17) for excessive water build-up. If necessary, hold a container beneath the Water Trap and press the button located at the bottom of the Water Trap to drain the water. 4. To clean the exterior of the Pressurized Abrasive Blaster, wipe with a clean, damp cloth using a mild detergent or mild solvent. Do not immerse the tool in liquids. 5. When storing, always store the Pressurized Abrasive Blaster in a clean, dry, safe location out of reach of children and other unauthorized peopl...