Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
If you need to lower the pres sure, it can be accomplished by these meth ods. 1. Back away from the sur face to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40. nozzle -this nozzle delivers a less powerful stream of water and a wider spray pattern. DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump. TO USE SPRAY WAND The nozzles for the spray wand are stored in the gatling spray wand. See chart to choose the correct nozzle for the job to be performed. CHANGING NOZZLES ON SPRAY WAND Risk of fl uid injection. Do not direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur. 11 - ENG A14687 A14687 12- ENG Risk of fl uid injection. Do Not attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 1. Press turret release button to release turret. 2. Rotate turret to chosen nozzle. 3. Push turret onto nozzle and lock into place. 0. 15. 40. Soap Spray Pattern Uses powerful pinpoint for very intense cleaning intense cleaning of small areas intense cleaning of larger areas applies cleaning solutions Surfaces * Metal or concrete DO NOT use on wood metal, concrete, or wood metal, concrete, or wood metal, concrete, wood, or vinyl * The high pressure spray from your pressure washer is capable of causing damage to surfaces such as wood, glass, automobile paint, auto striping and trim, and delicate objects such as fl owers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of the spray. HOW TO APPLY CHEMICALS AND CLEANING SOLVENTS Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To Apply chemicals: 1. Make sure the Barbed Fitting chemical hose is pressed onto the barbed fi tting located near high pressure hose connection of pump as shown. 2. Place other end of chemical hose with fi lter on it into container holding chemical/cleaning solution. NOTE: For every 7 gallons of water pumped 1 gallon of chemical/cleaning solution will be used. 3. Select the soap nozzle on the gatling spray wand, see o Use Spray Wand paragraph in this section. 4. After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty. NOTE: Chemicals and soaps will not siphon when spray wand is in the high pressure setting. TO EASILY REMOVE HOSE 1. Remove the accessory storage panel cover. 2. Remove hose from hose reel and replace accessory storage panel cover. To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual before starting pressure washer. Risk of fluid injection and laceration. When using the high-pressure setting, DO NOT allow the high-pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury will occur. • Your washer operates at fl uid pressures and velocities high enough to penetrate human and animal fl esh, which could result in amputation or other serious injury. Leaks caused by loose fi ttings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! Risk of Fire, Asphyxiation and Burn. NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. • NEVER fi ll fuel tank completely. Fill tank to 1/2" below bottom of fi ller neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine. • NEVER run engine in doors or in en closed, poorly ven ti lat ed areas. En gine exhaust con tains carbon mon ox ide, an odorless and deadly gas. • DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty. Risk of property damage. NEVER pull water supply hose to move pres sure washer. This could damage hose and/or pump inlet. • DO NOT use hot water, use cold water only. • NEVER turn water supply off while pressure washer engine is running or damage to pump will result. • DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged. If you do not understand these precautions, please call 1-800-888-2468 to speak to a service representative for further instructions. 13 - ENG A14687 STARTING Prior to starting, refer to your engine manual for proper starting procedure. 1. In...