Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Hold the gun and lance in a vertical position and squeeze the trigger to drain the water. Never store the pressure washer ! CAUTION with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. NOTE: To winterize unit, please follow the same intructions for Storage. TIPS FOR EXTENDING THE LIFE OF YOUR PRESSURE WASHER • NEVER operate the unit without water. • Your pressure washer is not meant to pump hot water. NEVER connect your pressure washer to a hot water supply as it will significantly reduce the life of the pump. • Running the unit for more than two minutes without spraying water causes heat to build up in the pump. Running the unit without spraying water can damage pump components. • Release the trigger prior to switching the lance between high and low pressure. Failure to do so may reduce the life of the o-rings in the lance. English — 15 MAINTENANCE Observe regular maintenance intervals to ensure maximum performance and life from the pressure washer. Refer to the schedule for recommended maintenance. If you operate the pressure washer in dusty conditions, perform maintenance checks more often. ENGINE OIL CHANGING INSTRUCTIONS Before tipping the engine or ! CAUTION equipment to drain oil, drain fuel from the fuel tank. NOTE: Change oil while the engine is cool. 1. Disconnect the spark plug wire from the spark plug. 2. Locate and remove the engine oil drain plug (see Figure 18). 3. Drain old oil. 4. Replace the drain plug and set the unit upright. 5. Refill the unit with new oil of a recommended type and quantity. Fill the unit to the proper level shown on the dipstick (if provided). Otherwise, fill the unit to the top of the oil filler neck. Engine Oil Type SAE 10W-30 SAE 30W (Above 60 °F/15.7° C) Engine Oil Capacity 5525PW - Honda GCV160 - 18.6 fl. oz. (0.550 L) 6027PW - Honda GX160 - 20 fl. oz. (0.591 L) 9032PW - Honda GX270 - 37 fl. oz. (1.090 L) 1340PW - Honda GX390 - 37 fl. oz. (1.090 L) Model 5525PW - Engine Oil Drain Plug Models 1340PW, 6027PW, and 9032PW - Engine Oil Drain Plug Figure 16 16 — English MAINTENANCE CHECKING PUMP OIL AND PUMP OIL CHANGING Checking oil level: Most pumps have either a sight glass or a dipstick (or both) to check the pump oil level. The correct oil level is at the center of the sight glass (center of red dot). The sight glass is usually located on the back side of the pump [See Figure 19 (B)]. (A) (B) (C) Figure 17 - Pump Oil Filler Vent Cap (A), Sight Glass (B), and Drain Plug (C) Locations For model 5525PW: Pump is factory sealed. Changing or refilling the oil in the pump requires removal of the pump from the engine and should not be required unless oil has leaked out due to worn or damaged oil seals in the pump. If oil has leaked out of the pump, bring the pressure washer to a certified service center for repair. For models 6027PW, 9032PW, and 1340PW: These units all have a sight glass to check the oil level and have a drain plug to remove the old oil when changing. To add oil remove vent cap from top of pump [See Figure 19 (A)]. Changing oil: Remove the oil drain plug located at the backside of the pump [See Figure 19 (C)]. Drain old oil. Replace drain plug. Refill pump with the correct type and amount of oil (see below for oil types and amounts). Check oil level. Upon starting the pressure washer check for any pump oil leaks. Pump Oil Type 5525PW -Lavor Pump - Special. See pump parts list. 6027PW, 9032PW, 1340PW - CAT Pumps Special CAT pump oil. Use 531 30 74-83. DO NOT use any oil in pumps other than the manufacturer's oil. English — 17 MAINTENANCE SCHEDULE Maintenance Schedule Action needed Each use • Check water inlet screen and filter. • Check engine and pump oil levels. Fill as necessary. Cannot check pump oil on the 5525PW. • Check gasoline level. Fill as necessary. After first 5 hours of operation • Change engine break-in oil. Use SAE30 or 10W-30 detergent oil if below 60° F (15.7° C). After first 50 hours of operation • Change pump oil. Cannot check or change pump oil on the 5525PW. Every 25 hours of operation • Change engine oil if operating under heavy load or high ambient temperature. • Remove and clean foam pre-cleaner or foam air filter (if applicable). Wash with water and mild detergent. Dry thoroughly. Rub with oil and squeeze to distribute oil. Every 50 hours of operation • Change engine oil. • Replace spark plug. Each 100 hours of operation or every 3 months • Clean or replace paper air cleaner cartridge. Tap gently to remove dirt. • Change engine oil. Every 500 hours of operation (5 months) • Change pump oil. Cannot check or change pump oil on the 5525PW. NOTE: This is a general maintenance schedule. Refer to the Engine operation manual for specific information on your engine. 18 — English TECHNICAL AND CONSUMER INFORMATION Pressure Washers Engine Oil Type SAE 10W-30 SAE 30W (Above 60 °F/15.7° C) Engine Oil Capacity 5525PW -Honda GCV160 - 18.6 fl. oz. (0.550...
Otros modelos de este manual:Equipo de lavado - 1340PW (4.55 mb)
Equipo de lavado - 6027PW (4.55 mb)