Iniciar sesión:
Votos - 2, Puntuación media: 5 ( )

Manual de usuario Graco Inc., modelo PCK3030SP

Fabricar: Graco Inc.
Tamaño del archivo: 1.23 mb
Nombre del archivo: 91d100e6-481a-4020-9679-4f103d226beb.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick when triggered. 10. Release trigger to stop water flow. 11. Adjust spray for the task being performed by changing quick connect nozzle. See How To Use Spray Wand instructions in this section. SHUTTING DOWN 1. After each use, if you have applied chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. NOTE: Failure to do so could cause damage to the pump. 2. Turn engine off. See Engine Owner’s Manual. NOTE: NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Storage section in this manual for proper storage procedures. Filter Screen High Pressure Hose Water Source D27927 14- ENG MAINTENANCE When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will be required. ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for any and all maintenance. PUMP NOTE: The pump was filled with oil at the factory. 1. Change pump oil after the first ten (10) hours of operation and every fifty (50) hours thereafter. To Check Oil: 1. Remove dipstick/oil plug from pump and wipe clean. 2. Insert dipstick/oil plug fully into pump, then remove it. 3. Oil level is correct when oil covers the lower 1/2 inch of end of dipstick/oil plug. How To Change Pump Oil 1. Loosen dipstick/oil plug. 2. Place a container under the oil drain plug. 3. Remove oil drain plug. 4. After oil is drained replace oil drain plug. Tighten securely. 5. Remove dipstick/oil plug and fill with recommended oil. See the Pump Oil Chart for the correct amount and type of oil. 6. Replace dipstick/oil plug and tighten securely. PUMP OIL CHART Dipstick/oil plug Oil Drain Plug Annovi Reverberi (XMV) 30W non detergent PUMP TYPE OIL TYPE 13.5 oz. OIL CAPACITY 15- ENG D27927 NOZZLE CLEANING If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions: 1. Shut off the pressure washer and turn off the water supply. 2. Disconnect spark plug wire. 3. Pull trigger on gun handle to relieve any water pressure. 4. Disconne...

Otros modelos de este manual:
Equipo de lavado - D27927-034-0 (1.23 mb)
Equipo de lavado - D27927-034-0 (1.23 mb)
Equipo de lavado - D27927-034-0 (1.23 mb)
Equipo de lavado - D27927-034-0 (1.23 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría