Votos - , Puntuación media: ( )

Manual de usuario Graco Inc., modelo Hydra-Clean 207-860

Fabricar: Graco Inc.
Tamaño del archivo: 343.14 kb
Nombre del archivo:

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

Refer to the separate lubricator instruction manual. Release the spray valve trigger and let the pump run. NOTE: Protect surfaces that might be damaged by the cleaning solution and rinse off before the solution dries. For removing stubborn dirt, use a strong, heated solution. Useful Hints WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. Hold the spray nozzle about 2 feet (0.6 m) from the surface you are cleaning and mist-wet it completely. Let it soak briefly, then use the spray to “chisel” the dirt off. Keep the nozzle at an angle, about 6 in. (150 mm) from the surface. If some dirt remains, wet the surface again. Let the object soak a little longer, then hold the nozzle as close as possible and spray to blast the dirt off. After the dirt is removed, through rinse off the remaining solution with clear, cold water. When you are done cleaning, close the pump air bleed valve and relieve the pressure. Shutdown and Care of Unit CAUTION To reduce the risk of damaging your pump. never allow the pump to run dry of fluid. Keep liquid in the container to prevent the pump from running away. WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. When shutting down for the day or weekend, shut off both the bleed–type air valve and pump air bleed valve. Relieve the pressure. Rinse off any solution remaining on equipment with clear, cold water. Shut off the water supply valve and relieve the water pressure. After shutdown, check the air line lubricator (G) often and keep it filled with oil. Also check the pump packing nut regularly and keep it just tight enough to stop leakage, but no tighter. Use a 1/4 in. diameter rod to tighten. . . Troubleshooting WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. Before servicing this equipment always make sure to relieve the pressure. Note: Check all possible problems and solutions before disassembling. Problem Cause Solution Excessive surge at spray nozzleExcessive surge at spray nozzle Obstructed spray tip, valve, or hose Clean, clear Cleaning solution supply empty Refill Clogged intake filter, kinked or collapsed suction hose Clean, unkink Fluid leaking from valve Loose packing nut or worn packings See manual 307–010 Valve will not stop dispensingalve will not stop dispensing Valve not adjusted properly See manual 307–010 Dirty or worn valve stem or seat Clean, clear, or replace – See manual 307–010 Valve will not stop the pumpalve will not stop the pump Cleaning solution supply empty Refill Clogged intake filter, kinked or collapsed suction hose Clean, unkink Dirty or worn valve stem or seat Clean clear, or replace – See manual 307–010 Dirty or worn fluid piston or packings Service – See pump manual Pump operating, but spray pressure low on up stroke. Dirty or worn fluid piston or packings Service – See pump manual Pump operating, but spray pressure low on down stroke Dirty or worn fluid intake valve Clean, clear, or replace – See pump manual Pump operating, but spray pressure low on both strokes Clogged intake filter, kinked or collapsed suction hose Clean, unkink Dirty or worn fluid piston or packings Service – See pump manual Dirty or worn fluid intake valve Clean, clear, or replace – See pump manual Loose packing nut or worn packings Tighten, replace – See pump manual Fluid will not come from pump (hose removed)(hose removed) Restricted air line Check for closed valve; use larger supply hose Pump throat packing nut too tight Loosen Pump air motor not working Service – See pump manual System will not spray Restricted air line Check for closed valve; use larger supply hose Pump air motor not working Service – See pump manual . . Service General WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 8. See Parts illustration for referenced items. Shut off the air supply to the pump and relieve the pressure. Check the air line lubricator often and keep it filled with oil. Also check the pump packing nut regularly to keep it just tight enough to stop leakage, but no tighter. Use a 1/4 in. (6.3 mm) diameter rod to tighten. To manually lubricate the motor, disconnect the air line at the motor and place 10 to 15 drops of oil in the inlet. Reconnect the air line and turn on the air to blow oil into the motor. Shut off the air supply to the pump and relieve the pressure. Proper packing nut take-up will stop leakage. However, all the packings should be replaced after 1000 hours of operation or delivery of 120,000 gallons of solution at 2 gpm. Refer to separate pump manual. Clean the air line filter regularly. Remove the inlet filter (2) daily and clean it. Check it for damage that may allow contaminants to en...