Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
To achieve best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes but do not let it dry. Rinse at high pressure using the high pressure lance in a sweeping motion keeping the tip of the spray nozzle at least 8-10 inches away from the surface. Maintain a further distance when using a direct spray. Wipe surface for a polished finish. 7 WARNINGDo not use pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. Ensure that all equipment and accessories are rated to withstand the maximum working pressure of the unit. WARNING• Always hold gun and lance firmly when starting and operating the machine. • NEVER allow the unit to run with the trigger released (OFF) for more than one minute. Resulting heat buildup will damage pump. • NEVERstore the pressure washer outdoors or where it could freeze. The pump will be seriously damaged. • This unit must always be used in the horizontal position.CAUTION WARNING WARNING DANGEREXTENSION CORDS DANGER WARNING Allowable Length Extension Cord 25' 50’ 14 AWG YES NO 12 AWG YES YES GETTING TO KNOW YOUR PRESSURE WASHER 1. Pressure Washer 2. On/Off Switch 3. High Pressure Water Output 4. Handle 5. Water Intake With Filter 6. Wheels ( x2) 7. High Pressure Lance 8. Brush 9. Trigger Gun 10. Safety Lock 11. Trigger 12. High Pressure Hose 13. High Pressure Hose Connector 14. Detergent Applicator Bottle 15. Garden Hose Coupling Technical Specifications Voltage: 120V., 60Hz. Power: 12.5 Amps. Pressure: 1450 psi. (max) Flow Rate: 1.45 gpm Illustrations may differ from actual product. 3 OPERATING INSTRUCTIONS OPERAT 6 When you wish to stop using the pressure washer temporarily, make sure that the safety lock has been engaged to avoid any accidental operation. (Fig. 5) Maintenance & Cleaning Cleaning the Nozzles: If you notice that the output pressure fluctuates, you may have to clean the nozzles. Turn the unit "Off". Unplug from electric outlet and disconnect the water supply. Remove the lance and hose with the trigger gun from unit. Take the small metal pin provided and insert into the nozzle end to remove any obstructions. (Fig. 9) When using your pressure washer, always have it in the horizontal position as shown below. NEVERhave it in the upright position. Using the High Pressure lanceThe high pressure lance may be used alone or with the detergent applicator bottle. Add detergent to the bottle and then attach the detergent applicator bottle to the high pressure lance, just push it on the end of the high pressure lance. (Fig. 6 & 7) To remove the detergent applicator bottle, lift the tab on the top of the connector and pull off. Fig. 5SafetyLockFig. 6 Fig. 9This will occur more frequently if your water supply is very hard. Lubrication: The pressure washer is supplied with a closed lubrication system, so no addition of oil is needed. Checking the Water Intake Filter: The water intake filter is located inside the water intake connector. (Fig. 8) Remove periodically and inspect for any deposits that might accumulate there. Fig. 8Hose Connector Water Intake CAUTION Fig. 7 CAUTION OPERATING INSTRUCTIONS Unpacking Your Pressure Washer After you open the package, check to make sure that all the parts are in the box as per parts that illustrated on page 3 of this guide. Due to transport and packing restraints, some accessories may be supplied unassembled; in this case follow the assembly instructions in this manual. If you have any questions, call Customer Service at 1-800-798- 7398. Keep all small and potentially harmful parts of the package (plastic bags, foamed polystyrene, nails, etc.) out of the reach of children. 4 OPERATING INSTRUCTIONS 5 Attaching High Presure Hose to Pressure Washer Garden Hose Connection 4. After all the connections have been made and BEFOREyou plug the pressure washer into an electrical outlet, open the water supply and press on the trigger switch in order to remove any air which may be in the hose or pump. Continue to press on the trigger switch until you get a constant flow of water coming out of the trigger gun. Allow water to flow for 30 seconds. 5. Once this is accomplished, stop pressing the trigger switch. Engage the safety lock on the trigger 6. Ensure that the "On/Off" switch, at the rear of the unit, is on the "Off" position, then plug the unit into an electrical outlet and turn the unit to the "On" position. 7. Now you are ready to use the pressure washer. Disengage the safety lock and depress the trigger on the trigger gun. 1. While facing the front side of the unit attach the high pressure hose to the high pressure output connector on the right side of the unit. Twist on tight to avoid leakage. (Fig. 2) To attach the lance to the trigger gun, hold the trigger gun in your left hand insert the lance and push it in all the way into the connector on the trigger gun and turn it clockwise 60° until it locks in place. To remove the lance, push down on the attac...