Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
If you find that they are not in good condition or are missing, please contact our customer service department for assistance. Our Toll-Free number is 1-877-337-3639. 12 HLP21E MANUAL 6/20/03 10:03 AM Page 15 English Proper Location General • Select a suitable location for the washer on a hard even surface away from direct sunlight and heat sources (e.g., radiators, baseboard heaters, cooking appliances, etc.). • Any floor unevenness should be corrected with the leveling leg located on the bottom right corner of the washer. • The washer must be placed at room temperature. You must not place the washer where the temperature is at or below freezing. Storage in Cold Environments • This appliance must be stored at room temperature. • If you received this appliance when the outside temperature is below freezing, do not operate until this appliance has warmed to room temperature. • Do not install or operate this appliance in an area where room temperature is below freezing. 13 HLP21E MANUAL 6/20/03 10:03 AM Page 16 English Installation Instructions Read carefully and understand all installation instructions before installing this washing machine. If after completing the process you are still unsure whether the washer has been properly installed, we recommend that you contact a qualified installer. Tools and Materials Required You will need to use the following tools when installing your washer: Scissors Phillips Screwdriver Flathead Screwdriver Pliers Wrench Tape Measure Gloves Level Installing the Bottom Panel The bottom panel blocks noises to provide you with the quietest performance possible during the wash cycle operation. 1. First, lay down the washer on its front side. 2. Place the panel against the bottom of the machine. Align the holes in the panel with the holes in the washer. 3. Insert the screws through the holes of the panel into the bottom of the washer and tighten. (8 screws are supplied) 4. Once all screws have been installed and the panel is in place, return the washer to its standing position. Note: During this time, you may reroute the drain hose to the left or right side for draining. 14 HLP21E MANUAL 6/20/03 10:03 AM Page 17 English Installing the Lint Filter The lint filter must be installed before the washer is used. The lint filter is packaged with the User Manual. Leveling the Washer Your washer has an adjustable leveling leg that is located on the front right corner. After properly placing your washer in its final location, you may level the washer. • Loosen the adjustable nut. The leveling leg can be adjusted by turning it counter-clockwise to raise the washer and clockwise to lower the washer. Note: If the washer is inclined more than 2°, the machine will not operate. Installing Your Washer Read the installation instructions carefully before beginning. 1. Connect the water inlet hose to the water faucet. Note: The ends of the inlet hose are marked red and yellow. Red goes to washing machine and yellow goes to the faucet. 2. Connect the other ends to the washer inlet located at the top rear of the machine. Insert a new flat washer (provided) to each end of the inlet hose. 3. The drain hose must be placed into a drainpipe or sink at least 1-1/2 inches in diameter. Use the gooseneck drain hook to hold the hose in place. To avoid possible water back-up, the drain hose must reach a height of at least 31-1/2 inches minimum and 40 inches maximum. 4. Plug in the washer to a regular 115 Volt / 60 Hz, 15 Amps outlet. Note: Carefully inspect for any leaks around the machine and at the back. If there is a leak, check if any connections are loose. You may need to tighten any loose connections. Do not remove the water absorption cushion. Check before each use to make sure it is not damaged. CAUTION! If after completing these steps you are still unsure whether unit has been properly installed, contact a qualified installer. We recommend that the washer be installed by a certified technician to ensure that it is properly installed. 15 HLP21E MANUAL 6/20/03 10:03 AM Page 18 English Installing Quick Sink Adapter: When installing the quick sink faucet adapter to the faucet, follow the steps below: 1. First, remove the aerator from your faucet nozzle and determine the size/type of the faucet. 2. Once you determine the size/type of the faucet (Outside Threaded End or Inside Threaded End), place the proper sized rubber washer into the silver faucet adapter. 3. Attach the silver faucet connector to the faucet. 4. Attach the faucet connector to the water inlet hose and make sure that the rubber washer is placed in between. 5. Attach the other end of the water inlet hose to the washer water inlet and make sure that the rubber washer is placed in between. Faucet Washers Faucet Adapter Quick Connector Water inlet hose Drain hose Washer Washer Rear View of Washer 16 HLP21E MANUAL 6/20/03 10:03 AM Page 19 English Unit Dimensions 29-15/16” 17-1/4” 17-5/8” 38-5/8” 17-1/4” 17-5/8” 17 HLP21E MANUAL 6/20/03 10:03 AM Pag...