Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Quick Set-up Guide 1 2 3 All three legs should be the same length to provide a level platform for the telescope. A bubble level is included (inset) to assist in leveling. 4 7 Hold the telescope fork arm and place the bottom of the base inside the tripod mounting platform as shown. Place accessory tray on top of center leg brace by lining up the grooves on the tray to the post on the brace. 5 Once grooves are aligned, turn accessory tray until it snaps into the clips on each leg brace. 6 Thread the coupling screw into the hole at the bottom of the fork arm base. Tighten screw to secure the entire fork arm. 8 Slide the optical tube dovetail into the fork arm as shown above. 9 NexStar 60SLT Your NexStar 60SLT includes: optical tube; fork arm; pre-assembled tripod; computerized hand control; hand control holder; star diagonal; two eyepieces; finderscope; accessory tray; documentation including an owner’s manual, The Sky® CD and NSOL Telescope Control Software. Item #22076 Coupling screw Extend tripod legs 6 to 8 inches by loosening the tripod leg locking knob and pulling the leg to desired length and re-tightening knob. Assemble tripod by spreading the legs out until the center leg brace is fully extended. Quick Set-up Guide 1 2 3 All three legs should be the same length to provide a level platform for the telescope. A bubble level is included (inset) to assist in leveling. 4 7 Hold the telescope fork arm and place the bottom of the base inside the tripod mounting platform as shown. Place accessory tray on top of center leg brace by lining up the grooves on the tray to the post on the brace. 5 Once grooves are aligned, turn accessory tray until it snaps into the clips on each leg brace. 6 Thread the coupling screw into the hole at the bottom of the fork arm base. Tighten screw to secure the entire fork arm. 8 Slide the optical tube dovetail into the fork arm as shown above. 9 NexStar 60SLT Your NexStar 60SLT includes: optical tube; fork arm; pre-assembled tripod; computerized hand control; hand control holder; star diagonal; two eyepieces; finderscope; accessory tray; documentation including an owner’s manual, The Sky® CD and NSOL Telescope Control Software. Item #22076 Coupling screw Quick Set-up Guide [cont] 10 11 12 Secure optical tube to fork arm by To attach the finderscope, loosen the silver Secure finderscope to mounting platform by tightening the screw located on the screw and slide finderscope into mounting tightening the silver screw. The glass window of inside of the fork arm assembly. platform . the finderscope should be facing towards the front of the telescope. 13 Insert the chrome barrel of the star diagonal into the focuser and tighten the two silver screws to secure in place. 16 Slide Computerized Hand Control into the hand control holder as shown above. 19 14 15 Select the low power (25mm) eyepiece and insert it as shown above. Tighten silver screw to secure. Attach plastic hand control holder to the tripod leg. 17 18 Plug Computerized Hand Control into the “Hand Control” port on the fork arm. Before you begin viewing, please remember to remove tube lens cap. 20 21 While observing, tube should be positioned as shown above. Before you can use your telescope, you must insert 8 AA batteries. Place AA batteries inside the battery compartment located at the base of the fork arm. Before you can begin observing, you must setup your hand control, align your finderscope and align your telescope. Step by step instructions are included in the following Hand Control Setup section. Hand Control Guide Before you can begin using your NexStar 60SLT, you must setup your computerized hand control and go through the SkyAlign alignment procedure. In order for the NexStar to accurately point to the objects in the sky, it must first be aligned with known positions (stars) in the sky. With this information, the telescope can create a model of the sky, which it uses to locate any object in its database 1 Turn power switch (located on the side of the fork arm) to “on” position. The light will come on and the hand control will display “NexStar SLT”. 2 You will notice that there are directional arrows in the center of the hand control. These only move the telescope. They cannot be used to scroll through menu features. 3 Now you will need to align the finderscope. Turn on the red LED light by turning the knob shown above. When used for the first time, remove the clear plastic disk that is located between the battery clip and the battery. See inset. Use the hand control direction arrow buttons to point telescope at a distant land object, like a telephone pole or at night you can use the moon. Center and focus the object in the 25mm eyepiece of the telescope. 4 In order to accurately center an object in the eyepiece it may be necessary to change the slew speed of the motors. To change the slew speed, press the RATE button then select a number from 1 (slowest) to 9 (fastest). 5 With the object centered in the eyepiece, use ...