Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
*Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. Missing one of the primary colors (RED, GREEN, or BLUE) *Inspect the monitor’s video cable and make sure that none of the pins are bent. INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor, do the following: . Carefully turn the monitor on its side or upside down. (see figure 1) . Locate the cavities at the bottom front of the monitor. . Insert the pegs on the swivel base into these cavities. Push the swivel base forward until the swivel base locks in place. . To remove the swivel base, hold the bottom of the swivel base, then push it out. POWER CORD Power Source: 1. Make sure the power cord is the correct type that required in your area. 2. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required). 3. Connect the power cord into your monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet. The power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your monitor. VIDEO CABLE Connecting the Video Cable: the monitor comes with a built-in video cable. Plug the signal cable.s 15-pin connector into the computer's video port and tighten the two screws on the cable connector. (see figure 2) Caution:Don’t bend the signal cable, otherwise it will break the inner wire. Connecting the Power Cord: Plug the power cord into the monitor's AC power jack. Then plug the power cord into a grounded AC outlet, UL-approved power strip, or the power output socket on your PC. Caution: If the AC outlet is not grounded, install the proper grounding adapter (not supplied). Connecting the Audio Cable ( CT740g only ): Plug audio cable between the computer multi-media (or sound) card's audio output and monitor's audio input. Connecting the DC Power Cable ( CT740g only ): Plug DC power cable between monitor to swivel base for audio power 5 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. . The power cord should be connected. . Connect the video cable from the monitor to the video card. . To turn the monitor on, press the power switch to ON position. The power indicator will light up. . Your monitor features a unique quick switch system which provides a picture within seconds after the monitor is switched on. NOTES . Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. . Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. . For maximum protection, repackage your monitor as it was originally packed at the factory. . To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it. Figure 1 Installing and Removing the Swivel Base Figure 2 Connecting Cables Figure 3 External Control Knob 1 2 3 1 2 3 4 5 7 6 6 ADJUSTING THE PICTURE 1. CONTRAST Adjust the picture contrast. 2. BRIGHTNESS Adjust the picture brightness. 3. H- CENTER Adjust the horizontal position of the picture. 4. H- SIZE Adjust the picture’s horizontal size. HOW TO ADJUST A SETTING 1. Press the Shuttle Knob Key to make the OSD window appear. See figure 4. 2. Rotate the Shuttle Knob to select the desired function. See figure 4. 3. Press the Shuttle Knob again to select the function that you want to adjust. 4. Rotate the Shuttle Knob to change the settings of the current function. 5. When the OSD window is active, it shows the input signal timing. The "H" stands for the horizontal frequency and "V" for the vertical frequency. 6. To exit and save, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. 1024 X 768 Figure 4 The OSD Message CONNECTING CABLES 1. Power Cord 4. PC Audio Output 2. Signal Cable 5. DC Output 3. VGA Card Adapter EXTERNAL CONTROLS 1. Shuttle Knob 2. Power Indicator 3. Power button FRONT PANEL CONTROL PANEL CONTROL . Power button : When pressed, the monitor enters the off mode, and the LED flashes. Press again and hold to restore normal status. . Shuttle Knob : The Shuttle Knob is used to control the monitor functions. Rotate to switch functions or adjust settings. Press to select or execute a function . . Power Indicator : Green — Power On...
Otros modelos de este manual:Monitores - CT700G (598.84 kb)