Votos - 1, Puntuación media: 4 ( )

Fabricar: LG Tamaño del archivo: 5.5 mb Nombre del archivo: Idioma del manual:

Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity. 2 Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame; wipe in one direction only. Too much moisture may cause staining. On Repacking Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material. On Disposal Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 3 4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) DVI-D Signal Cable (This feature is not available in all countries.) NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. Connecting the Display Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Body Hinge Body Stand Body Stand Base 4. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 5. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on the surface. cushion or soft cloth. 3. Remove the Stand Body and Stand 4. Use a coin on the back of the Stand Base from product in correct Base and turn the screw anticlockdirection as shown in the picture. wise to loosen. 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5. to 15. ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, Do not touch or press the screen whenadjusting the angle of the monitor. When adjusting the angle of the screen, donot put your finger(s) in between the head ofthe monitor and the stand body. You canhurt your finger(s). the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display E2241V/E2341V/E2341VG/E2441V Connecting the Display E2241V/E2341V/E2341VG/E2441V Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 1 2. Connect signal input cable and power cord 2 in order, then tighten the screw of the signal cable. Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable A B NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. PCPCABWall-outlet type Mac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. When using a D-Sub signal ...

Descargar ahora

Introduzca dos números de la imagen: