Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Your monitor may differ from the items shown in the picture. yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Mounting on a table 1 Lift and tilt the Monitor set into its upright position on a table. Leave a 10 cm (minimum) space from the wall for proper ventilation. 3 Press (Power) button on the bottom switch panel to turn the power on. CAUTION Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur. 10 cm 10 cm 10 cm 10 cm Using the cable holder 2 Connect the AC-DC Adapter and Power Cord to a wall outlet. Cable holder or WARNING Using the Kensington security system When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers. The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the Monitor set and a table. Do not touch or press the screen when adjusting the angle of the monitor. Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body. NOTE The Kensington security system is optional. You can obtain it from most electronics stores. NOTE Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view. Rear Front Model E1642CE1942CE2042CE2242C VESA (A x B) 75 x 75 Standard screw M4 Number of screws 4 Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 10 cm CAUTION 10 cm yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur. yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury. yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel. yy Do not over tighten the screws as this may cause damage to the Monitor set and void your warranty. yy Use only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. 10 cm 10 cm If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop. 1 Please, Use the screw and wall mount interface in accordance with VESA Standards. 2 If you use screw longer than standard, the monitor might be damaged internally. 3 If you use improper screw, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it. 4 VESA compatible. 5 Please use VESA standard as below. yy784.8 mm (30.9 inch) and under * Wall Mount Pad Thickness : 2.6 mm * Screw : . 4.0 mm x Pitch 0.7 mm x Length 10 mm yy787.4 mm (31.0 inch) and above * Please use VESA standard wall mount pad and screws. NOTE yyUse the screws that are listed on the VESA standard screw specifications. yyThe wall mount kit will include an installation manual and necessary parts. yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer. yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length. yyFor more information, refer to the instructions supplied with the wall mount. USING THE MONITOR SET 9 ENG ENGLISH USING THE MONITOR SET Connecting to a PC yyYour Monitor set supports Plug & Play*. *Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention. D-SUB connection Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations. NOTE yyWhen using a D-Sub signal input cable connector for Macintosh yyMac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector. USING THE MONITOR SET 10 ENG ENGLISH Self Image Setting Function Press the power button on the bottom panel to turn the power on. When monitor power is turned on, the "Self Image Setting" Function is executed automatically. (Only supported in Analog Mode) CAUTION yyConnect the signal input cable and tighten it by turning the screws clockwise. yyDo not press the screen with your finger for a long time as this may result in temporary distortion on the screen. yyAvoid displaying a fix...
Otros modelos de este manual:Monitores - E1942C (2.5 mb)
Monitores - E1942C-BN (2.5 mb)
Monitores - E2042C-BN (2.5 mb)
Monitores - E2242C (2.5 mb)