Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
• Make sure the signal cable is properly connected to your computer. • Make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable. • The Energy Saving feature may be activated Screen says Check cable connection • Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Star t Guide). • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. AUTO button doesn't function • The auto function is applicable only in VGA-Analog mode. If the result is not satisfactor y, you can do manual adjustments via the OSD menu. Note The Auto Function is not applicable in DVI- Digital mode as it is not necessar y. Visible signs of smoke or sparks • Do not perform any troubleshooting steps • Disconnect the monitor from mains power source immediately for safety • Contact with Philips customer ser vice representative immediately. Imaging Problems Image is not centered • Adjust the image position using the “Auto” function in OSD Main Controls. • Adjust the image position using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Image vibrates on the screen • Check that the signal cable is properly securely connected to the graphics board or PC. Vertical fl icker appears • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the ver tical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Horizontal fl icker appears • Adjust the image using the “Auto” function in OSD Main Controls. 39 8.Troubleshooting & FAQ8.Troubleshooting & FAQs • Eliminate the ver tical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Image appears blurred, indistinct or too dark • Adjust the contrast and brightness on On-Screen Display. An "after-image", "burn-in" or "ghost image" remains after the power has been turned off. • Uninterrupted display of still or static images over an extended period may cause "burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burnin", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off. • Always activate a moving screen saver program when you leave your monitor unattended. • Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content. • Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “after-image” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Image appears distorted.Text is fuzzy or blurred. • Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution. Green, red, blue, dark, and white dots appears on the screen • The remaining dots are normal characteristic of the liquid cr ystal used in today’s technology, Please refer the pixel policy for more detail. The "power on" light is too strong and is disturbing • You can adjust “power on” light using the power LED Setup in OSD main Controls. For fur ther assistance, refer to the Consumer Information Centers list and contact Philips customer ser vice representative. 8.2 SmartControl Premium FAQs Q1. I change the monitor on a PC to a different one and the SmartControl Premium becomes un-usable, what do I do? Ans.: Restar t your PC and see if Smar tControl Premium can work. Otherwise, you will need to remove and re-install Smar tControl Premium to ensure proper driver is installed. Q2. The SmartControl Premium functions worked well before, but it does not work anymore, what can I do? Ans.: If the following actions were executed, the monitor driver may need to be reinstalled. • Changed video graphic adapter to another one • Updated video driver • Activities on OS, such as ser vice pack or patch • Run Windows Update and updated monitor and/or video driver • Windows was booted with the monitor power off or disconnected. • To find out, please right click My Computer and click on Proper ties->Hardware-> Device Manager. • If you see “Plug and Play Monitor” shows under Monitor, then you need to re-install. Simply remove Smar tControl Premium and re-install it. 40 8.Troubleshooting & FAQ8.Troubleshooting & FAQs Q3. After installing SmartControl Premium, when clicking on SmartControl Premium tab, nothing shows up after a while or a failure message shows, what happened? Ans.: It might be your graphic adaptor is not compatible with the Smar tControl Premium. If your graphic adaptor is one of the above mentioned brands, tr y to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove Smar tControl Premium, and re-install it once more. If it is still ...