Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Your product automatically acquires all the network setting values it needs and connects to your network. • PIN: Input the displayed PIN on your device. . If you want to disconnect the device, select the connected Wi-Fi device, and then select Disconnected. Soft AP MENU m >Network >Soft AP >ENTER E Using this function, you can connect the product on your mobile devices if your mobile devices do not support Wi-Fi Direct. Set the options for connection of Wi-Fi device. • Soft AP Turns on or off the Soft AP. When Soft AP is set to On, your mobile devices can find the product name in Wi-Fi connection list. • Security Key Set the Security Key manually using the remote control. -B Show security key: Shows the security key. Whether to show the security key is represented by a checkbox at the top. -A Del.: Deletes the entered security key one digit at a time. - C Space: Inserts a blank space between characters when entering the security key. - Return: Returns to the screen before entering the security key. - The Security Key should consist of more than 8 digits. - Input the generated security key into the device you want to connect. - If network does not operate normally, check the security key again. An incorrect security key may cause a malfunction. AllShare Settings MENU m >Network >AllShare Settings >ENTER E Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play function with this product. • Allow / Deny: Allows/Blocks the devices. • Delete from the list: Deletes the devices from the list. . This function only deletes the name of the device from the list. If the deleted device is turned on or tries to connect to the product, it may appear on the list again. Using the AllShare Play Function An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile phone will be displayed on your product. The contents are played automatically 3 seconds after the alarm window appears. If you press the RETURN or EXIT button when the alarm window appears, the media contents are not played. . The first time a device accesses your product through the media function, a warning popup window appears. Press the E button to select Allow. This permits the phone to access the product freely and use the AllShare Play function to play content. . To turn off media contents transmissions from a mobile phone, set Deny in the AllShare Settings. . Contents may not play on your product depending on their resolution and format. . The E and / buttons may not work depending on the type of media content. . Using the mobile device, you can control the AllShare Play. For details, refer to each mobile’s user’s guide. Device Name MENU m >Network >Device Name >ENTER E Select or enter a device name. This name can be shown on network remote controls over the network. 121System Chapter 08 Multi Control MENUm >System >Multi Control >ENTERE Multi Control ID Setup ID Input MDC Connection DisplayPort daisy chain 00 RS232C MDC Clone -The displayed image may differ depending on the model. Configuring settings for Multi Control •ID Setup Assign an ID to a set. (Range: 0~99) Press or to select a number, and press E. •ID Input Enter the ID number of the product connected to the input cable for input signal reception. Enter the number you want using the number buttons on the remote control. •MDC Connection Select a method to connect to MDC to receive the MDC signal. -RS232C MDC: Communicate with MDC via the RS232C-stereo cable. -RJ45 MDC: Communicate with MDC via the RJ45 cable. •DisplayPort daisy chain To display the DP IN video input through the DP OUT output port, select a device connection method from Single Stream Transport (SST ) and Multi Stream Transport (MST ). Clone: In this Single Stream Transport (SST ) output mode, the same screen output is displayed on two display devices connected. .If Clone is selected, the PC recognizes the two displays as a single monitor. Expand: In this Multi Stream Transport (MST ) mode, a different screen output is displayed on two display devices connected. .If Expand is selected, the PC recognizes the two displays as separate monitors. .The mode functions only on a PC that supports DisplayPort 1.2 MST. .For Full HD resolution (1920x1080) displays, a maximum of four displays can be connected. 121System Chapter 08 Multi Control MENUm >System >Multi Control >ENTERE Multi Control ID Setup ID Input MDC Connection DisplayPort daisy chain 00 RS232C MDC Clone -The displayed image may differ depending on the model. Configuring settings for Multi Control •ID Setup Assign an ID to a set. (Range: 0~99) Press or to select a number, and press E. •ID Input Enter the ID number of the product connected to the input cable for input signal reception. Enter the number you want using the number buttons on the remote control. •MDC Connection Select a method to connect to MDC to receive the MDC signal. -RS232C MDC: Communicate with MDC via the RS232C-stereo cable. -RJ...