Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
2 MUTE button Switch the audio mute ON/OFF. 3 INPUT button Use this button to select the input source. 4 [] button Increase the adjustment while OSD menu is on, or increase the audio output level while OSD menu is off. 5 [] button Decrease the adjustment while OSD menu is on, or decrease the audio output level while OSD menu is off. 6 [] button Move the highlight bar up to adjust the selected item while OSD menu is on. 7 [] button Move the highlight bar down to adjust the selected item while OSD menu is on. 8 MENU button Return to previous menu while OSD menu is on, or to activate the OSD menu when OSD menu is off. NOTE: “Keyboard Control Lock Mode” This function completely disables the access to all Keyboard Control functions. To enable or disable the keyboard control lock, press both [] and [] buttons and hold down continuously for more than 3 (three) seconds. 9 Remote control sensor and power status indicator • Receives command signals from the remote control. • Indicates the operating status of the display without OPS: --Lights green when the display is turned on --Lights red when the display is in standby mode --Lights amber when the display enters APM mode --When {SCHEDULE} is enabled, the light blinks green and red --If the light blinks red, it indicates that a failure has been detected --Lights off when the main power of the display is turned off • Indicates the operating status of the display with OPS: --Lights green when the display is on, but the OPS is off --Lights blue when the display and the OPS are on --Lights red when the display is in standby mode --Lights amber when the display enters APM mode --When {SCHEDULE} is enabled, the light blinks green and red --If the light blinks red, it indicates that a failure has been detected --Lights off when the main power of the display is turned off BDL4677XH 2.2. Input/Output Terminals 8171819201234761011121415165913 1 AC IN AC power input from the wall outlet. 2 MAIN POWER SWITCH Switch the main power on/off. 3/ 4 IR IN / IR OUT Reserved for the wired connection of the IR control. NOTE: If an external IR receiver is connected to [IR IN], there is no function on the display’s remote sensor. 5 RS232C OUT: RS232C network output for the loop-through function. 6 RS232C IN RS232C network input for the loop-through function. 7 RJ-45 LAN control function for the use of remote control signal from control center. 8 HDMI IN HDMI video/audio input. 9 DisplayPort DisplayPort video input. 10 DVI IN DVI-D video input. 11 DVI OUT / VGA OUT DVI or VGA video output. 12 VGA IN (D-Sub) VGA video input. 13 VGA AUDIO IN Audio input for VGA source (3.5mm stereo phone). 14 COMPONENT IN (BNC) Component YPbPr video source input. 15 Y/CVBS Video source input. 16 SPEAKER SWITCH Internal speaker on/off switch. 17 AUDIO IN Audio input from external AV device (RCA). 18 AUDIO OUT (RCA) Audio output from the AUDIO IN jack to an external AV device. 19 SPEAKERS OUT External speakers output. 20 OPS SLOT Slot for installing the optional OPS module. BDL4677XH 2.3. Remote Control 2.3.1. General functions POWERSMARTVIDEOSOURCEPIPINPUTON/OFFCHANGEBRIGHTNESSCONTRASTDISPLAYAUTOADJUSTMUTEVOL UPVOL DOWNEXITMENUSETAUDIOSOURCEUSB MENU110111213141516171819202345678921 1 [POWER] button Press to switch on the display from standby mode. Press again to turn it off and back into standby mode. 2 [SMART] button Press to activate Smart Menu. Press [] or [] button to select menu options. Press [SET] button to confirm and exit the selection. • Standard: Used for normal images (factory setting) • Highbright: Used for moving image such as Video • sRGB: Used for text based images(only for PC mode) • Cinema: Used for movies(only for Video mode) 3 [PIP] (Picture In Picture) button [ON/OFF]: Turn PIP mode ON/OFF. [INPUT]: Select the input signal for the sub-picture. [CHANGE]: Toggle between the main picture and sub picture. 4 [CONTRAST] button Press to activate Contrast Menu. Press [] or [] button to adjust the value. 5 [DISPLAY] button Press to turn on/off the information OSD displayed on the upper right corner of the screen. 6 [] button • Press to move the selection left in OSD menu. • Press to decrease the value in OSD menu. • Press to move the sub-picture left in PIP mode. 7 [SET] button Press to activate the setting inside the OSD menu. 8 [AUTO ADJUST] button Press to run the Auto Adjust function. NOTE: This button is functional for VGA input only. 9 [MUTE] button Press to turn the mute function on/off. 10 [VIDEO SOURCE] button Press to toggle Video Source Menu. Press [] or [] button to select one of the video sources among Displayport, DVI-D, VGA, HDMI, Component, Video, Card OPS. Press [SET] button to confirm and exit. 11 [AUDIO SOURCE] button Press to toggle Audio Source Menu. Press [] or [] button to select one of the audio sources among Displayport, HDMI, Audio1, Audio2 or Card OPS. Press [SET] button to confirm and exit. 12 Picture Format button Press to switch screen aspect ratio. • For PC signal: FUL...