Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
• Locate your monitor near an easily accessible electrical outlet. • Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched with a sharp or abrasive implement. • Put your monitor in a location with low humidity and a minimum of dust. • Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep the cable away from where people could trip over it. • Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. • To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor’ s case. • Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet. • Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface. Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some other enclosed space, be sure to provide adequate ventilation. • Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure to unplug the monitor first. • If your monitor does not operate normally—in particular, if there are any unusual sounds or smells coming from it—unplug the monitor immediately and contact an authorized dealer or service center. Connecting Your Monitor to a Computer 1. Turn off your computer and display, then unplug the power cable. 2. Remove the door. 3. Connect the 24-pin DVI-D connector of signal cable to the DVI-D video port on the back of computer. Tighten screws securely with fingers. Connect the speaker cable to the lime colored phone jack on the back of computer. Connect the microphone cable to the pink colored microphone jack on the back of computer. Dell 1401FP Flat Panel Color Monitor Quick Setup Guide 4. Route the USB cable under the DVI-D cable, then connect it to the USB port. 5. Connect the power cable for your monitor to the power port on the base. Connect the power cable for your computer to the power port. 6. Secure all long cables under the cable guide. 7. Attach door into position. 8. Plug the power cable of the display into the outlet. 9. Plug the power cable of the computer into the outlet. If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting. Monitor Controls and Indicators 1. For Brightness use this button to decrease or increase brightness. 2. The Power button turns the monitor on and off. The Power indicator lights steady green, amber, yellow or blinking steady yellow indicates the power management state of the monitor. Driver Installation Use the monitor CD to install the appropriate monitor driver for your operating system. Microsofta Windowsa 98 Operating System Windows 98 automatically detects the new monitor and displays the Add New Hardware Wizard dialog box if the monitor driver is not already installed. 1. Insert the monitor CD into the CD-ROM drive, and click Next> twice when the Add New Hardware Wizard dialog box appears. 2. Click the CD-ROM drive box to install the drivers from the CD and then click Next>. 3. Confirm that the driver was found on the CD, and click Next> twice to install the driver. 4. Click Finish to exit the Add New Hardware Wizard dialog box. To manually install or update the driver, perform the following steps: 1. Click Start-> Settings-> Control Panel and then double-click Display. 2. In the Display Properties window, click the Settings tab, and then click Advanced. 3. Click the Monitor tab, and then click Change. 4. When the Update Device Driver Wizard dialog box appears, follow the steps in the previous paragraph. Microsoft Windows 95 Operating System First determine the Windows 95 version installed on your computer by right-clicking the My Computer icon on the desktop and selecting Properties. The version number is listed under System. Perform the steps for the appropriate version. Version 4.00.950A 1. Click Start-> Settings-> Control Panel and then double-click Display. 2. In the Display Properties window, click the Settings tab and then click Change Display Type. 3. In the Change Display Type window, click Change and then click Have Disk. 4. Insert the monitor CD into the CD-ROM drive, type d:\ (change the drive letter to match your CD-ROM drive if it is not drive D) in the Copy manufacturer’ s files from: box, and click OK. 5. In the Select Device window, click the appropriate monitor model and then click OK. 6. In the Change Display Type window, click Close. 7. In the Display Properties window, click OK. Dell 1401FP Flat Panel Color Monitor Quick Setup Guide Version ...