Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
CAUTION 1. Do not operate the monitor at temperatures below 32°F (0°C) or above 104°F (40°C). 2. Keep the monitor clean and dry. 3. Always seek qualified personnel to perform repairs. Never attempt your own repairs. 4. Do not drop the monitor or expose to strong impacts. 5. Do not expose to direct sunlight for extended periods of time. The Materials included in this package: 1. LCM500NP Monitor (1pc) 2. Remote Control Unit (1pc) 3. Interconnection Box (AVX-6865) (1pc) 4. Monitor Cable Assembly 16 Feet (5 Meters) (1pc) 5. Power Cable Assembly (1pc) 6. Surface Mount (S2) (1pc) 7. Headrest Shroud (1pc) 8. Trim Ring For Shroud (1pc) 9. Removal Tool (1pc) LCM500NP SYSTEM OVERVIEW The LCM500NP is comprised of a 5" Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) monitor. The monitor display is a widescreen display (16:9 Aspect Ratio ) that allows the user to select from two video sources (Not Supplied). The housing has a built-in location for the installation of an optional infrared audio transmitter ( Audiovox IRT 456, IRT 457) for use with optional two channel wireless headphones. The monitors will display all functions with the comprehensive On Screen Display (OSD). OPTIONAL AUDIO CONNECTION Required Materials: 1. IRT456 (CHA) Infrared Transmitter (1pc) 2. IRT457 (CHAB) Infrared Transmitter Remote (1pc) 3. WHS200 Two Channel Infrared Headphones Before installing the IRT boards gently bend the three IR LEDs closest to the center of the vehicle toward the center of the vehicle. IRT 457 CH B BEFORE IRT 456 CH A BEFORE IRT 456 CH A AFTER IRT 457 CH B AFTER Insert the IRT boards into their respective compartments in the monitor housing and insert the plug into the IRT board. When the user switches the video source utilizing the ON/OFF/MODE switch, the A/B switch on the WHS200 headphones must also be switched to select the desired audio source. -1 VEHICLE PREPARATION: 1) Decide on the system configuration and the options that will be installed (i.e.what components, VCP, DVD, TV Tuner, Video Game, Monitor, FM Modulator, etc.). 2) Read the manuals and get familiar with the electrical requirements and connections. 3) Decide on the mounting locations and methods of mounting the products. 4) Prepare the vehicle by removing any interior trim necessary to gain access to the vehicle's wiring as well as all areas where interconnecting wire harnesses will be located. If any access holes need to be cut into the vehicle, headrests, or other trim components, this should be performed now. (Refer to the Installation Procedure). 5) Run the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagram on page 7, as well as the wiring instructions for the individual components and accessory options being installed). Be sure, that all the wiring is protected from sharp edges and is routed in such a manner that it will not be pinched, when it is fully installed. Be sure to leave enough slack in the wiring at each component to allow sufficient working room. 6) Remove all the A/V system components from their packaging and then place them in the vehicle at their respective locations. 7) Connect all the components together (electrically) and verify the proper operation of all the system functions. NOTE: This is best done BEFORE the components are permanently mounted. 8) After verifying the proper operation of the system, proceed to mount each component. 9) When all the components are mounted, recheck the function of the entire system to be sure it is functioning correctly. Make sure that no wiring was pinched, or connected improperly during the final installation. 10) Locate the following: an accessory power source (+12VDC present when the ignition key is in the accessory and run positions). 0VDC should be present, when the ignition key is in the OFF position. A constant power source (+12VDC present at all times). Generally, these wires can be found at the ignition switch or fusebox. (NOTE: Ensure that the power leads are fused at the source. Failure to do so may result in vehicle wiring damage.) Ground the black wire to a chassis ground close to the mounting location of AV sources. 11) The mounting method, and the location will vary from vehicle to vehicle, so this manual will only focus for the installation of the LCM500NP Monitor in the supplied configuration. 12) The best location for the LCM500NP System components are: a) Monitor : Headrest b) Interconnection Box: Under either seat where monitors are located. -2 Tools and Materials Required: • Utility knife or box cutter with sharp blade • Sharpie™ marker or similar • Tie Wraps Remove the headrest from the vehicle for easiest installation. Lay headrest on a flat surface Center trim collar on headrest as shown. NOTE: Depending on the angle of the headrest the trim ring and housing may be mounted upside down. Using a Sharpie™ marker or similar marking pen, mark headrest material along the interior of the trim collar. Remove the trim collar and mark an “X” fr...
Otros modelos de este manual:Monitores - LCM500NP (216.12 kb)