Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
• Press the menu button and activate the Self-Diagnosis menu to determine whether your monitor is functioning normally, not receiving a signal or is receiving a signal that is out of scanning range. • Activate the higher refresh rates of the monitor to stabilize the screen and eliminate the annoying flicker that contributes to eye-strain and headaches. • The “borderless” full-screen display capability works under all graphic modes and provides a larger viewing area than conventional monitors, giving you a better picture with more workspace. English - 2 SETUP INSTALLING THE TILT/SWIVEL STAND 1. Ensure that the power to the monitor is off. 2. Set the monitor face down with the underside facing you. Please be careful so as not to scratch the monitor screen. 3. Align the four hooks on the stand with the guide holes of bottom chassis of the monitor. 4. Insert the hooks into the guide holes. 5. Slide the tilt/swivel stand toward the front of the monitor until the latch locks in position. 6. Turn the monitor and the stand upright. If you want to remove the tilt/swivel stand on the monitor, press the latch and pull the tilt/swivel stand toward the back of the monitor. Lift the stand to separate. Latch English - 5 OPERATION & ADJUSTMENT Control Panel • Launch OSD(On-Screen Display) MENU window. • Select a sub Menu & function. • Move a sub Menu & function. • Increase the value of any selected function. • Adjust the contrast directly when there is no OSD. • Move a sub Menu & function. • Decrease the value of any selected function. • Adjust the brightness directly when there is no OSD. SELECT ADJUST MENU MENU SELECT English - 4 CONNECTING THE SIGNAL CABLE AND POWER CORD 1. Turn off the computer and monitor. 2. Connect the 15 pin D-sub connector to the output port of the video card in your computer. 3. Tighten the screws of the connector. 4. Plug the power cord into the AC receptacle located on the back of the monitor. 5. Plug the other end of the power cord into the AC outlet. If your power cord is PC-to-Monitor type, plug the other end of the power cord into the AC receptacle in the computer. Signal Cable Power Cord Key Pr ocess OSD Functions OSD Functions ICON CONTROL FUNCTION Adjust the position of the display H. POSITION horizontally (left or right). MENU SELECT MENU Adjust the position of the display V. POSITION vertically (up or down) . Adjust the display width (horizontal H.SIZE size). V.SIZE Adjust the display height (vertical size). MENU MENU V. LINEARITY Adjust the vertical linearity. H. LINEARITY PINCUSHION OSD OFF Adjust the horizontal linearity. Adjust the left and right margins for more convex or more concave margins. Adjust the trapezoid of the screen by TRAPEZOID • When you choose the icon on the OSD window, you can moving the lines inward or outward. exit the OSD screen. Adjust the side balance when the sides of PIN BALANCE the screen are bowed towards left or right. Adjust the parallelogram when the PARALLELOGRAM screen is leaning left or right. Adjust the pin corner top when the top T. PIN CORNER sides of the screen are bowed. Adjust the pin corner bottom when the B. PIN CORNER bottom sides of the screen are bowed. English - 6 English - 7 ICON CONTROL FUNCTION Adjust the side pin corner balance T. PIN BALANCE when the top sides of the screen are bowed towards left or right. Adjust the side pin corner balance bottom B. PIN BALANCE when the bottom sides of the screen are bowed towards left or right. Choose different preset color temperatures COLOR TEMP or set your own customized color parameters. RED GAIN Adjust the red gain. GREEN GAIN Adjust the green gain. BLUE GAIN Adjust the blue gain. RED BIAS Adjust the red bias. GREEN BIAS Adjust the green bias. BLUE BIAS Adjust the blue bias. LANGUAGE Select language for OSD (5 languages). Degaussing keeps the monitor free from DEGAUSS unwanted magnetism that can result in color impurity. English - 8 ICON CONTROL FUNCTION Display horizontal & vertical frequency STATUS and polarity. Adjust the horizontal picture moire H. MOIRE cancellation. Adjust the vertical picture moire V. MOIRE cancellation. Reset the screen to the Factory Preset RECALL Display Settings. Adjust the rotation when the screen is ROTATION tilted left or right. Self Diagnosis When the monitor doesn’t display, if you press any control key, Self Diagnosis screen is displayed. Self Diagnosis function checks if the status of the monitor is No Signal or Out of range. No Signal screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode. Out of Range screen is displayed when the applied frequency is under or over normal range. Normal range H : 30 - 70 KHz V : 50 - 160 Hz English - 9 SPECIFICATIONS TROUBLESHOOTING CDT Size 17-inch Diagonal visible image area 16.2-inch Dot Pitch 0.27 mm Synchronization Horizontal 30 - 70 KHz Vertical 50 - 160 Hz Plug and Play DDC1/2B/CI Power Saving EPA, VESA DPMS, Nutek Compliant Power Source 100-240 Vac, 50/60Hz (...