Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure. WHAT TO DO IF… WARNING! Before troubleshooting, disconnect the mains plug from the mains socket. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. There are some sounds during normal use (compressor, refrigerant circulation). Problem Possible cause Solution The appliance does not The appliance is switched off. Switch on the appliance. operate. The Pilot light does not flash. The Pilot light flashes. The mains plug is not connected to the mains socket correctly. The appliance has no power. There is no voltage in the mains socket. The appliance is not working properly. Connect the mains plug to the mains socket correctly. Connect a different electrical appliance to the mains socket. Contact a qualified electrician. Contact a qualified electrician. The Alarm light flashes. The temperature in the freezer is Refer to "High temperature too high. alarm" 5) If foreseen. What to do if… 13 Problem Possible cause Solution The compressor operates continually. The temperature is not set cor- rectly. Set a higher temperature. The door is not closed correctly. The door has been opened too frequently. The product temperature is too high. The room temperature is too high. The FROSTMATIC function is switched on. The temperature in the The temperature regulator is not freezer is too low. set correctly. The FROSTMATIC function is switched on. The temperature in the The temperature regulator is not freezer is too high. set correctly. The door is not closed correctly. The product temperature is too high. Many products are stored at the same time. Products are too near to each other. A large quantity of drops There is too much frost and ice ice covers the top com on the evaporator of the appli partment inside the appli ance, the door was open for too ance. long time. Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". Refer to "Closing the door". Do not keep the door open longer than necessary. Let the product temperature decrease to room temperature before storage. Decrease the room temperature. Refer to "FROSTMATIC function". Set a higher temperature. Refer to "FROSTMATIC function". Set a lower temperature. Refer to "Closing the door". Let the product temperature decrease to room temperature before storage. Store less products at the same time. Store products so that there is cold air circulation. Refer to "Cleaning the evaporator". 3. If necessary, replace the defective door gaskets. Contact the Service Center. Cleaning the evaporator 1. Switch off the appliance. 2. Disconnect the mains plug from the mains socket. 3. Remove all foods from the freezer and put them in a fresh place. 4. Move the appliance far from the wall. 5. Leave the door open. 14 14 Technical data 6. After approximately 20 minutes the drain hose at the rear of the cabinet starts to discharge water into the drip tray. 7. To prevent the water overflowing from the drip tray dry with a sponge. 8. The defrosting process ends when the water stops dripping. It may take several hours if the problem started long before. 9. Move the appliance to the original posi- tion. 10. Clean and dry the inside of the appli- ance. 11. Connect the mains plug into the mains socket. 12. Switch on the appliance. TECHNICAL DATA Dimension of the recess Height 1600 mm Width 600 mm Depth 630 mm Rising Time 21 h Voltage 230-240 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. INSTALLATION WARNING! Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance. Location The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet. To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm . Ideally, however, the appliance should not be positioned below overhanging wall Installation 15 units. Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet. If the cabinet is placed in a corner and the side with the hinges facing the wall, the distance between the wall and the cabinet must be at least 10 mm to allow the door to open enough so that the shelves can be removed. WARNING! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation. 10mm10mm100mm Positioning WARNING! If you are discarding an old appliance that has a lock or catch on the door, you must ensure that it is made unusable to prevent young children being trapped inside. The appl...