Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
3 - Dimensions of the appliance 600 min 550 820- 890 595 548 min 25 819- 889 100- 170 fig. 3 Fig. 4 - Fitting the worktop bracket Remove the screw (5) on the top of the appliance, locate the top bracket(6) and fix the bracket with screw(5). fig. 4 5 6 Fig. 5 - Fitting the spacer piece Take out the spacer piece (11) located on the side panel and remove the protective tape. Stick the spacer piece on the opposite side to the door hinges of the appliance. 11 11 11 11 fig. 5 Installation Fig. 6 - Adjusting the appliance height The height of the appliance can be adjusted by the help of adjustable feet to fit the furniture height. Use a spirit level to ensure the appliance is level. Fig. 7 - Aligning the appliance Slide the appliance into the kitchen unit and align the hinge surface with front surface of the kitchen unit. Fig. 8 - Fixing the appliance Screw the hinges and metal bracket to the kitchen unit using screws (1) 9 fig. 8 fig. 6 fig. 7 7 7 8 9 1 1 Installation Fig. 9 - Fitting the decor door bracket Unscrew and remove the nuts and washers from the appliance door. Place fixing bracket on the appliance door by inserting the holes to adjustment bolts. Dimension B= Measure from the underside surface of kitchen unit to the bottom of fixing bracket. Dimension C= Measure from the underside surface of kitchen unit to the top of next unit door. Fig. 10 - Fitting the decor door bracket Substract C from B and put the fixing bracket (2) in place using this measurement for vertical position and place to the centre for horizontal position. Secure the fixing bracket (2) using screws(1). Fig. 11 - Fitting the decor door Place the decor door onto the appliance door by inserting adjustment bolts into the slots on the fixing bracket. Locate the washers and screw the nuts onto the adjustment bolts. fig. 9 C B fig. 11 fig. 10 2 1 B-C Installation Fig. 12 - Aligning the decor door Close the door and check the alignment with the other unit doors. Adjust the decor door by screwing or unscrewing the adjustment bolts for vertical adjustment and by the help of the slots on the fixing bracket for other directions. Lock the screws into place as shown in 10.2. 1010 8 fig. 12 Fig. 13 - Fitting the decor door base fixings With the appliance door open, remove the screws at the bottom of the appliance door. Locate the decor door base fixings (3) and screw the fixings to the appliance door and the decor door. fig. 13 1 3 Fig. 14 - Fitting the decorative cover Fit the decorative cover (4) on the decor door fixing bracket. 4 fig. 14 Installation Fig. 17 - Fitting the plinth Fit the plinth section, providing minimum 25 mm gap between the cabinet door and fix it. Never cover over the ventilation slots. Once installed the plinth must not block the ventilation slots in the appliance. This may require cutting the plinth down. Failure to ensure adequate ventilation may invalidate the warranty. fig. 17 min 25mm Fig. 17 - Fitting the plinth Fit the plinth section, providing minimum 25 mm gap between the cabinet door and fix it. Never cover over the ventilation slots. Once installed the plinth must not block the ventilation slots in the appliance. This may require cutting the plinth down. Failure to ensure adequate ventilation may invalidate the warranty. fig. 17 min 25mm Reversing the door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Open the door. 2. Loosen the hinge fixing screws (1) and remove the door. 3. Remove the door fixing screws (2). 4. Remove the cover caps (3). 5. Relocate the hinges as shown. 6. Refit the door to the hinges. Do not turn the door upside down 7. Insert the cover caps (3) on the opposite side in the exposed holes. fig. 18 Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to prevent the risk of electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: • The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELLOW. • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or coloured BLACK. • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or coloured RED. I...