Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
This turntable is manufactured to the highest degree of tolerance and quality. Please take a moment to read this owner’s manual to ensure correct set up, to avoid any possible damage and to learn how proper care of your clearaudio ChampionLevel 1 turntable which will give you many years of musical enjoyment and pleasure. clearaudio electronic GmbH Contents 1. Front view 3 2. Package contents 4 3. Assembly and Operation 6 4. Speed calibration 9 5. Special instructions 9 6. Service 9 7. Technical data 11 Page 2 . clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 1. Front view The photo below shows the clearaudio ChampionLevel 1 turntable assembled and set up with the Unify tonearm. You can see the use of carefully selected materials and the resonance avoiding construction. Further the stand-alone Motor reduces any induced vibrations and resonances to the turntable chassis. ChampionLevel 1 assembled and set up 2. Package contents The clearaudio ChampionLevel 1 turntable is delivered in a special packaging to ensure its safe transport. Please check the contents as shown in the picture below and in the list on the next page: Page 3 . clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 1 2 4 3 6 5 9 7 8 10 11 12 13 14 15 16 17 Overview of package contents Not shown: a pair of white gloves 1. Champion acrylic chassis with mounted bearing 10. Champion acrylic chassis (lower part) 2. Complete preassembled stand-alone motor 11. REGA-counterweight 3. Decuppeling device for the motor 12. REGA-tonearm base nut 4. Three Flat Pads to be lawn under the Spikes 13. Complete preassembled REGA-OEM tonearm 5. Pulley made out of acrylic including fixing screws 14. Tube of grease for servicing the platter bearing 6. Grounding cable to ground the bearing screw 15. High-precision turntable platter made out of solid silicon acrylic 7. clearaudio Clever Clamp 16. Hex key wrenches : one to adjust the tonearm height, the other for the screws to mount the base 8. Precision level gauge 17. Screw-driver made out of aluminium 9. Two drive belts (one spare) Page 4 . clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 3. Assembly and Operation First please put on the white gloves to avoid finger prints on the surface of the acrylic chassis during installation. 1. Place first the lower part-chassis on a clean and soft surface. Please pay attention, that the surface of your HiFi-rack is horizontal and vertical correctly adjusted, by using the delivered level gauge. Important: Never turn the Spikes of the turntable chassis, they had been adjusted in the factory. Use the delivered Flad Pads to avoid scratches on the surface of your HiFi-rack. After that place the chassis with the mounted bearing onto the first one. 2. Now unpack your turntable platter and place the platter carefully on the upper part of the bearing which is mounted in the turntable chassis. Important: take care not to cause to much pressure! 3. Place the pulley on the motor spindle. The distance between the pulley and the motor housing should be approx. 1-2mm. Tighten the little screws inside the pulley with the aluminium screwdriver provided. Page 5 . clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 4. Place the decuppeling base for the motor in the indent of the chassis and place the motor on it. The switch of the motor should be on the outside of the turntable and the space between motor and chassis approx. 1cm. (for an exact adjustment see chapter 4). 5. Please screw the tonearm carefully into the upper part of the tonearm base. Then slide the tonearm nut over the tonearmcable and tighten it, but not too much because the tonearm should be still able to turn. 6. Now you can While holding the unit you can adjust the tonearm height (VTA = vertikal tracking angle) when you have a cartridge mounted. The VTA is adjusted correctly if the tonearm sits parallel to the turntable platter surface after lifting it down. Now loosen the six screws with the provided hex key wrench, to be able to set the distance between the spindle and the tonarm bearing crosspoint to 222mm, by turning the tonearm base. After that you can fix the six srews again. Page 6 . clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 7. Turn the tonearm into the final position where the tonearm is almost parallel to the right hand edge of the chassis. After that you can fix the tonearm in this position by holding the tonearm nut with one hand and turning the tonearm against, while using the other hand or tight the large nut with a wrench. Mount the tonearm counterweight. 8. To change the height of the tonearm lift, turn it up to the high position and loosen the little screw at the front. Now you can move the plate of the lift. The distance between record and cartridge diamond when it is lifted up should be about 5mm. Tighten the screw again. 9. Place the belt first round the platter, then round the smaller diameter of the pulley (33 1/3 rpm). 10.The tension of the belt...