Votos - 3, Puntuación media: 5
(
)
)
|
Fotos y especificaciones Marantz TT-15S1 |
Resumen del manual
7 Equipment Main Power Setting Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. TT-15S1 can be powered by 120V AC only. 7 Copyright Recording and playback of any material may require consent. For further information refer to the following: -Copyright Act 1956 -Dramatic and Musical Performers Act 1958 -Performers Protection Acts 1963 and 1972 -Any subsequent statutory enactments and orders 7 Do Not Locate in the Following Places To ensure long-lasting use, do not locate the TT-15S1 where: • Exposed to direct sunlight. • Near to sources of heat such as heaters. • Highly humid or poorly ventilated. • Dusty. • Subjected to mechanical vibrations. • On wobbly, inclined or otherwise unstable surfaces • Radiated heat is blocked such as in cramped audio racks. To ensure proper heat radiation, ensure the below clearance from walls and other equipment. Front0.2m0.2m0.2m Side 0.2m0.2m0.2m 7 Caution: Do not lose the bearing. (View from underneath the turntable chassis) Bearing Turntable chassis Center shaft hole Center shaft There is a bearing located inside the center shaft hole in the turntable chassis. When the turntable leaves the factory, the center shaft hole is covered with tape to prevent the bearing from falling out. Sometimes after removing the tape, the bearing falls out when the turntable is turned over. If the center shaft is inserted when there is no bearing in the center shaft hole, the turntable will not rotate. Therefore, make sure that the bearing does not fall out of the center shaft hole when assembling the turntable. Furthermore, if the turntable is disassembled for transportation etc. cover the center shaft hole with tape etc. to prevent the bearing from falling out. 7 Before using • Thoroughly remove dust or dirt from the stylus point and record. If you play records when there is dirt/dust on the stylus, not only will the stylus have poor contact with the record causing poor sound quality, it will also increase the rate of wear of both the stylus and record. Gently remove dirt/dust by brushing with a soft tipped brush from the base of the stylus to the tip. Also wipe the record with a good quality record cleaner. • Install the turntable chassis and turntable so that they are level. It is possible to adjust the height of the legs by rotating them. However, as there are only 3 legs, the height may not be adjustable in some cases. In such cases, adjust the rack itself so that it is horizontal. • About howling and hum Howling occurs when sound from the speaker or vibration is transmitted to the player and is picked up by the cartridge again. If howling occurs when the volume is increased, check the positions of the speakers and turntable, and move them to locations where neither vibration nor sound is transmitted to the turntable. Hum noise occurs because of electromagnetic waves that are generated from other electronic devices. Check the position of other electronic devices that are near to the turntable, especially the amplifier. Also, hum or noise occurs if the ground is not connected correctly. Check that the ground wire is securely connected to the GND terminal on the amp/mixer. ACCESSORIES ACCESSORIES Before using the turntable, please make sure that you have all of the following accessories. 1. Turntable chassis 5. Motor 2. Center shaft 6. Motor pulley (for 60Hz areas) 3. Tone arm 7. Gloves (pair) 4. Turntable 8. Ground wire ACCESSORIES ACCESSORIES 9. 2 Drive belts (1 spare belt) 13. Record clamp (“Clever clamp” produced by Southern Engineering) 10. Bearing oil 14. Counter weight 11. Turntable sheet 15. Tone arm height adjustment sheet 12. 3 Allen wrenches (large/medium/small) 16. Cartridge (MM type) by Clearaudio 1 adjustment screwdriver ASSEMBLING AND ADJUSTING ASSEMBLING AND ADJUSTING 1. Installing the ground wire 4. Attaching the tone arm Connect the ground wire to the turntable shaft base. a) Pass the Phono cable that is connected to the tone arm through the tone arm attachment hole. Tone arm phono cable Turntable chassis Turntable shaft base Ground wire 2. Inserting the center shaft Insert the center shaft into the turntable chassis. Center shaft Turntable chassis 3. Installing the turntable Place the turntable onto the center shaft. Turntable Center shaft b) Determine the height and direction of the tone arm attachment position. b-1)Height Bear in mind that the height position of the tone arm is different depending on whether or not the turntable sheet is used. • When using the turntable sheet The correct height position is achieved when the counter weight and tone arm height adjustment sheet are placed beneath the arm lifter. With turntable sheet Arm lifter Counter weight Tone arm height adjustment sheet • When not using the turntable sheet The correct height position is achieved when just the counter weight is placed beneath the arm lifter. (Tone arm height adjustment sheet is not used.) No turntable sheet Arm li...