Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Tone arm height 1. Release the arm lock. 2. Adjust the arm height. •Adjust the ring using the chart below as reference so the arm height matches the indicated height of the cartridge. Measurements are marked on the arm height control ring in 0.5 millimeter intervals. Index line Fit the dust cover SL-1210M5G Hold the dust cover with both hands and fit it over the player from directly above. SL-1200GLD Place the dust cover in position from directly above, holding it at both sides. For detaching the dust cover, be certain first to raise it as illustrated before removal. •If you do not know the height of your cartridge, rest the stylus on a record and adjust the height control until the tone arm and record are parallel. 3. Lock the arm after adjusting the height. Armlift screw Armlift 1 Locked3 Released Arm height control ring Tone arm and record parallel. Balance weight measurement units Cartridge height (H) in millimeters 17 18 19 20 21 22 23 Height control position 0 1 2 3 4 5 6 RQT7021 8 When the player is to be used for scratch play. Use the disc slip sheet instead of the turntable mat. This enables the record to be easily moved during play. •Top (printed side): Lay the record on this side. •Bottom: Slippery side. For a different kind of slip Put the transparent sheet under the disc slip sheet. Playing records Preparation 1. Put a record on the turntable. 2. Take off the stylus cover and release the arm clamp. 1 Turn [power] to turn the unit on. •The pilot lamp comes on. •33 1/3 r/min is automatically selected and the indicator lights. •Press [45] if you are playing a 45 r/min record. 2 Press [start-stop]. The turntable starts revolving. 4 Lift the cue lever and move the tone arm over the record. 5 Lower the cue lever. The tone arm moves down and play starts. 3 Press [reset] to light the pitch control green LED lamp. The pitch returns to 33 1/3 or 45 r/min. Use the above indicated pitch for playing standard music. To temporarily stop play Lift the cue lever. The stylus lifts off the record. Refer to page 9 for fine adjustments to the pitch When using EP records 1. Take the EP record adaptor out of its holder and fit it over the center spindle. 2. Press [45] to change the speed. When play finishes 1. Lift the cue lever and move the tone arm back to the arm rest. 2. Press [start-stop]. The electronic brake gently stops the turntable. 3. Turn [power] to turn the unit off. 4. Clamp the tone arm and put the stylus cover back on. To light up the stylus •Press the stylus light switch. A blue LED light rises up and illuminates the stylus. •When the light is not required, press it down. The light also goes out. Press the switch firmly. If the switch is lightly pressed, the light may come on but not rise up. 1 3 2 4,5 33 45 Indicator lights start • stop 33 Cue lever EP record adaptor Disc slip sheet Transparent sheet Stylus light switch Stylus light off on power Pilot lamp Green LED indicator reset Adjustments while using the unit Pitch control Adjusting tone arm horizontal weight to reduce skipping when scratch playing. Fine adjustment to the number of revolutions per minute. 1 Press [reset] to turn off the green LED light. 2 Press [±16/±8] to select the pitch. •When [±16/±8] is pressed once (up position), the [±16] pitch indicator lights on the pitch control slider. •When [±16/±8] is pressed twice (down position), the [± 8] pitch indicator lights on the pitch control slider. Green LED indicator Pitch control Variable range pitch button reset 3 Slide [pitch adj.] while the turntable is revolving. Move the control to the required position. •The numbers represent approximate percentages. •Pitch can be adjusted between –8 % and +8 % or –16 % and +16 %. To reset pitch to the preset value Press [reset]. The green LED indicator lights and the pitch immediately returns to the set value (33 1/3 or 45 r/min), regardless of any adjustments made with [pitch adj.]. Press [reset] again and pitch returns to the adjusted value. To measure pitch The four rows of strobe mirrors around the edge of the turntable can assist you in measuring pitch. +6.4 % change in pitch when stationary +3.3 % change in pitch when stationary Normal turntable speed when stationary _3.3 % change in pitch when stationary They are lit by the strobo light as they pass and each row appears to stand still at a different pitch. offpower Strobo light Read the pitch control slider replacement instructions that comes with this product carefully when replacing the pitch control slider. The horizontal weight of the tone arm can be adjusted using the horizontal weight control knob on the gimbal suspension to reduce skipping when scratch playing. For scratch play Turn the knob all the way in the “A” direction to apply horizontal weight. For normal play Turn the knob all the way in the “B” direction to reduce horizontal weight. •Do not move the horizontal weight control knob when playing music. Horizontal weight control knob 0 6 When the horizontal weight control knob...
Otros modelos de este manual:estéreo - SL-1200GLD (746.19 kb)