Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Re-loop (Returns to a loop) After releasing a loop, press [EXIT/RELOOP] during play •Returns to the loop in point previously set and begins loop play again. When using CD-R, CD-RW MP3 files •When you reverse play while using cue point, cue pad or re-loop, reverse play is not effective beyond the set starting point. Play from the stored point Play after back cueing After performing back cue, press [PLAY/PAUSE] •Play begins from the set point. Correcting the cue point 1. Perform back cue 2. Perform steps 2-4 in the Setting the cue point at any point section again. ( page 17) •A new cue point is stored to memory. Playing from the CUE PADS Press one of the lit [CUE PADS 1-4] •Even if you are playing, play immediately begins from the point stored to the CUE PADS . When paused in the TURNTABLE mode, the platter begins to turn and play. •During play of the CUE PADS, if you press the same pad again, play will repeat from the beginning of the memorized point. •During play of the CUE PADS, if you press a different pad, play will switch to the selected pad. Stopping cue pad play Press [PLAY/PAUSE] •The PLAY/PAUSE lamp flashes and play pauses. Note Note Storing panel data to this unit (TURNTABLE mode only) •The unit stores following panel data for each CD or SD Memory Card. It can store data for up to 50 CDs or SD Memory Cards. •Auto Cue on, off and auto cue level •Cue bank •Instant change •Loop in, Loop out •Cue pad 1-4 •Dynamic effect •Vinyl simulator •If the unit’s memory exceeds 50 CDs or SD Memory Cards worth of data items, a message indicating replacement appears in the display and data items will be overwritten and replaced in the order of the oldest used first. •You can save this panel data for each CD or SD Memory Card to a SD Memory Card. ( page 21, Saving to a SD Memory Card) •In CD player mode, panel data cannot be automatically stored or read. Automatic read when media inserted (TURNTABLE mode only) •When media with recorded data is inserted into the unit, the settings are automatically read. While the unit is reading the media, each of the lamps for the cue pad 1 to 4, CUE, LOOP IN, and OUT flash rapidly, and are set in order. Pushing the cue pad, or the CUE or loop play buttons while the lamp is flashing rapidly will give that pad or button priority to be set, and then played. The start of play may be delayed. When reading has completed, the lamps stop flashing, and remains lit. MP3 files on CD-R and CD-RW, or SD audio take more time to read than CD audio. Use only once the lamp has stopped flashing and remains lit after pressing the cue pad, or the CUE or loop play buttons. •The lamps may flash rapidly while the media is being read even when carrying out other operations. •Removing the media, or switching [PLAY SELECT] erases the settings, however re-inserting the media restores the settings. Recording to the SAMPLE PADS and playing You can record audio to the sample pads for replay. You can record up to a maximum total of 32 seconds using SAMPLE PADS 1-4. Recording to the SAMPLE PADS in real-time 1. Press [REALTIME REC] while media is being played •All SAMPLE PADS, CUE PADS 1-4 pad lamps and CUE lamp flash. •Press [REALTIME REC] again to cancel. 2. Press one of the [SAMPLE PADS 1-4] and recording starts •The selected SAMPLE PADS lamp flashes. • indicator changes to in the display. •Previous pad data is erased at the start of recording if it exists. •Recording automatically ends when the pads total recording time reaches 32 seconds. 3. At the end point press the same sample pad again •The SAMPLE PADS lamp changes to a stationary light and recording ends. • indicator reverts back to in the display. •You can also control the platter slip surface and adjust the tempo during recording. •You can also edit sample pad data. ( page 20) •Recorded sample pad data is erased when the power is turned off. To avoid losing data you can save to the SD Memory Card. ( page 21, Saving to a SD Memory Card) Playing from the SAMPLE PADS Press one of the lit [SAMPLE PADS 1-4] •The lamp of the pad you pressed begins to flash and play begins. •During play, if you press one of the lit sample pads, dual play begins and mixed sound is output. You can perform dual play using up to 2 sample pads. •Once the end of the play is reached the SAMPLE PADS lamp changes to a stationary light. Play ends if you press the pad again during play. •When playing only the sample pad, the platter slip surface does not rotate even in the TURNTABLE mode. •When playing media, you can mix sound by also playing the sample pad. Sound may become distorted depending on the audio level. You can adjust the sample pad level. ( page 20, Editing the SAMPLE PADS) Select play mode and play 1. Press [SAMPLE EDIT] and select “PLAY MODE SELECT” •Play mode selection is not possible when nothing has been recorded to the sample pad. Each time you press the button: LEVEL EDIT WRITING START END PLAY MODE SELECT OK? START : (Edit the data starting point) END : (Edit the dat...