Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
The center speaker is not used in the simulated mode. D Select the desired source and start the desired source. B Press SFC to select the desired SFC mode. Each time the button is pressed, the indicator will change in the order: LIVE —THEATER —SIMULATED To turn off the SFC function Press OFF/ON. Press once again to turn it on. To adjust center and surround speakers volume E mm Center speaker volume can be adjusted only in the THEATER mode. To adjust center speaker volume Press CENTER (-) or (+) To adjust surround speaker volume Press SURROUND (-) or (+). Adjusting the sound Held and sound quality Adjusting the sound field and sound quality I n POWER Equalization-level display EQ LEVEL El A»— BQWUZERl£VaOOW7HOl ■ A I I I I I I I ) EQ ON/OFF :6 Using the graphic equalizer I For SD-S948»S748,SH-GS71 Adjusting the tone qualify I Preparation I • Turn Dolby Pro Logic and the SFC mode OFF. • Set the TREBLE and BASS tone controls to their center positions. O Press POWER of the graphic equalizer. The graphic equalizer will switch on. B □ Start the desired sound source. Press EQ LEVEL. (The equalization-level display will be shown.) Adjust the left and/or right channel tone quality as desired. (See below.) Upper row: These buttons are used to increase the level of each sound range (frequence range). Lower row: These buttons are used to reduce the level of each sound range (frequency range). Caution As with any equalizer, it is not recommended to raise adjacent equalizer level controls by a large amount. This may cause amplifier clipping, distortion, or damage to the speakers. It is more effective to raise one equalizer level control and lower the ones on either side, especially if you want to emphasize a particular sound like a drum. To bypass the graphic equalizer D Press EQ ON/OFF to select the "EQ OFF" mode. Press once again to turn on the equalization effect. For your reference Bypass is possible even when power to the graphic equalizer is OFF. Characteristic of each frequency range The followings are the examples of typical applications with regards to the equalizer band settings. These statements are used in a general manner of speaking and may not hold true in all cases. I 63 Hz | Deep bass range The sounds of the bass, drums, etc. are dramatically strengthened. I 160 Hz | Bass range This range provides the sounds of the saxophone, trombone, etc. sounds can be clarified, if indistinct, by reducing this setting. I 400 Hz I Mid-bass range (the fundamental range for music) This control can be used to reinforce the sounds of male vocals, etc. II kHz | Mid-range This control can be used to add clear presence and realism to female vocals, etc. 12.5 kHz I Mid-high range This range provides clarity and color variations to stringed instruments, etc. 16.3 kHz I Treble range This control can be used to brighten the sounds of the flute and similar instruments. If sounds seem too jarring, a softness can be applied by reducing the setting. 42 |12.5 kHz| Super-treble range This control can be used to provide an extra measure of delicate vibration to the sounds of the cymbals, triangle, etc. If tape "hiss" noises are annoying, this control's setting can be reduced to alleviate such noises. Using the graphic equalizer 1 ¿»1!H To change the spectrum display The spectrum display exhibits 3 types of display. Press one of the corresponding display mode select buttons. □ > When BAR button is pressed The bar-type display is shown. This display can be used to show the output strength for each sound range (frequency range), and to show the output strength of sound for all ranges (full range) by a bar-type display. 1*4»« njuwMoa • When DOT button is pressed The dot-type display is shown. This display can be used to make the strength of the sound for each sound range even easier to see. • When PEAK HOLD button is pressed The peak-hold display is shown. This display can be used to show the peak sound value of each sound range for about two seconds after it occurs. To produce a reversed equalization curve I This feature can be used, for example, to listen to the original sound characteristics of a tape that has been recorded with special equalization effects by using the graphic equalizer. a B Display the curve used when the recording was made. Press REVERSE. The reverse indicator will illuminate and the reversed equalization curve will be displayed. The playback sound will then be corrected by this curve, and will become a flat characteristic. Press once again to return to previous condition. 43 Adjusting the sound field and sound quality Adjusting the sound field and sound quality I MEMORY tu— «AM ItAHt ftXvAAMK I 1 I » I 3 I 4 1 5 I 8 I b Using the graphic equalizer For SD-S948»S748»SH-GS71 To retrieve pre-programmed equalization curves □ This unit has been pre-programmed with six types of typical equalization curves which are appl...