Votos - 4, Puntuación media: 4.5 ( )

Fabricar: Kenwood Tamaño del archivo: 999.31 kb Nombre del archivo: Idioma del manual:

This unit may not function properly if condensation occurs. In this case, leave the unit for a few hours with the power left ON, and restart the poeration after the condensation has dride up. Be specially cautious against condensatin in a following circumsatance: When this unit is carried from a place to another across a large difference in temperature, when the humidity in the room where this unit is installed increases, etc. In regardto contact cleaner Do not use contact cleaners because it could cause a malfunction. Be specially careful not to use contact cleaners containing oil, for they may deform the plastic component. Note related to transportation and movement (CD player) Before transporting or moving this unit, carry out the following operations. 1. Turn the power ON. 2. Unload the discs 3. Close the disc tray. 4. Turn power off. When your unit needs to be repaired, bring the entire set (Speakers excluded) to your dealer. 28 In case of difficulty 28 In case of difficulty XD SERIES (En) What seems to be a malfunction is not always so. Before calling for service, check the following table according to the symptom of your trouble. Operation to reset The microcomputer may fall into malfunction (impossibility to operate, erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, execute the following procedure to reset the microcomputer and return it to normal condition. Press the "POWER" key while holding the Stop (7) key of the CD section pressed, to switch off the power, and then switch the power on again after a few seconds. O Please note that resetting the microcomputer clears the contents stored in and returns and to condition when it left the factory. Receiver, speakers Symptom Cause Remedy Sound is not produced. O The speaker cords are disconnected. O The MUTE switch of remote control unit is switched ON. O The headphone plug is inserted into the jack. O Connect properly referring to “System connection”. O Switch MUTE OFF. O Unplug the headphone plug. 9 % % Sound is not produced from the left or right speakers. O The speaker cords are disconnected. O Connect properly referring to “System connection”. 9 Demonstration starts suddenly. O The power plug was unplugged from the outlet while the power switch was ON, or there was a power failure. O This is not malfunction. Press the DISPLAY/ DEMO key to cancel the demontration.4 The clock display blinks O There was a power failure. O The power cord was unplugged from the outlet. O Adjust the present time again. O Adjust the present time again. # # Timer operation is not possible. O The present time has not been adjusted or there was a power failure. O The timer ON time and OFF time have not been set. O The timer execution was not set up. O Adjust the present time referring to “Clock adjustment”. O Set the timer ON time and OFF time. O Execute the timer program. # ° ¤ Radio stations cannot be received. O The antennas have not been connected. O A proper broadcasting band has not been selected. O The frequency of the station to be received is not tuned. O Connect antennas. O Select a band. O Tune to the frequency of the desired station. 8 ) ) Noise interferes. O Car ignition noise. O Influence of an electric appliance. O A TV set is installed near the system. O Install the outdoor antenna in an apart position from the road. O Switch the suspected electric appliance OFF. O Install the TV or the system at an increased distance between them. 8 A station has been preset but it cannot be received by pressing the P.CALL key. O The frequency of the preset station is not tunable. O The preset memory has been cleared because the power cord has been unplugged for a long period. O Preset stations with tunable frequencies. O Preset stations again. A A Knowledge 29In case of difficulty 29In case of difficulty XD SERIES (En) Remote control unit Symptom Cause Remedy Remote control operation is not possible. O Batteries are exhausted. O The remote control is too far away from the system, the controlling angle is deviated or there is an obstacle in between. O There is no tape or CD set in the component to be played. O Replace with new batteries. O Operate the unit inside the remote controllable range. O Set a tape or CD in the component to be played. @ @ ^ Cassette deck Symptom Cause Remedy Sound cannot be produced by pressing O The head is dirty. O Clean the head referring to “Maintenance”. ¦ the play key or no operation occurs even O The tape is wound too tight due to irregular O Try another tape. . when an operation key is pressed. winding. O A nonrecorded tape is played. O Play a recorded tape. No operation occurs even when an operation key is pressed. O The cassette holder is not closed completely. O A tape is not inserted in the unit. O The tape is wound too tight due to irregular winding. O The tape is fully wound to one of the reels. O Close the holder completely. O Insert a tape. O Try another tape. O Re...

Descargar ahora

Introduzca dos números de la imagen: