Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
want them to be recorded (refer to “CD Operation - Programming the disc tracks”). 2 Press RECORD to star t recording. . The disc will star t playback automatically. To stop recording . Press C. . Recording and disc playback will stop simultaneously. . Playing and recording will star t simultaneously. . "DUB" is displayed. . Dubbing of tapes is possible on one side of the tape only. To continue recording on the reverse side, at the end of side A, flip the tape to side B and repeat the procedure. To stop dubbing . Press C. Notes: – Dubbing of tapes is possible only from tape deck 1 to tape deck 2. –To ensure good dubbing, use tapes of the same length. External Sources SOUND MAX Listening to external sources 1 Connect the audio out terminals of the external equipment (TV,VCR, Laser Disc player, DVD player or CD Recorder) to the AUX/CDR terminals of your system. 2 Press AUX to select external equipment. . "AUX" or "CDR" is displayed. Note: – All the sound control features (DSC or DBB, for example) are available for selection. – Refer to the operating instructions for the connected equipment for details. For Recording, please refer to “Tape Operation/Recording”. 23 24 English Clock/Timer IMPORTANT! – When in Eco Power standby mode, it is not possible to operate the clock or timer function. – Use CLOCK•TIMER (CLK•TIMER) to set the clock and timer. View clock The clock (if it is set) will be shown in standby mode. To view the clock in any source mode (CD or TUNER for example) . Press CLOCK•TIMER. . The clock is displayed for a few seconds. . If the clock has not been set, "--:--" is displayed. Clock setting The clock can be set in either 12-hour or 24-hour mode ("AM 12:00" or "00:00" for example) 1 In standby or view clock mode, press CLOCK•TIMER once. In other source mode, press CLOCK•TIMER twice. 2 Press PROGRAM repeatedly to select clock mode. . "AM 12:00" or "00:00" starts flashing. 3 Press a or a on the system repeatedly to set the hour. 4 Press i or e on the system repeatedly to set the minute. 5 Press CLOCK•TIMER again to store the setting. . The clock starts working. To exit without storing the setting . Press Con the system. Notes: – The clock setting will be cancelled when the power cord is disconnected or if a power failure occurs. – During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically. – To set the clock automatically through the time information in the RDS signal, refer to "Radio Reception - Setting the RDS clock". DISC DSC VAC ALBUM REC . SHUFFLE VAC DBB INC SURR SOUND MAX Clock/Timer Timer setting The system can switch on to CD,TUNER, or TAPE 2 mode automatically at a preset time, ser ving as an alarm to wake you up. IMPORTANT! – Before setting the timer, ensure that the clock is set correctly. – The timer will always be switched on after it has been set. – The timer will not start if a recording is in progress. – The volume of the timer will increase gradually from the minimum level to the last tuned volume level. 1 Press and hold CLOCK•TIMER for more than two seconds to select timer mode. . The last timer setting star ts flashing. . TIMER star ts flashing. . The selected source will be lighted and flashing. 2 Press CD, TUNER or TAPE to select the desired source. . Before setting timer, make sure the music source has been prepared. CD – Load the disc(s).To star t from a specific track, make a programme (refer to “CD Operation - Programming the disc tracks”). TUNER – tune to the desired radio station. TAPE – load the prerecorded tape into tape deck 2. 3 Press a or a on the system repeatedly to set the hour for the timer to star t. 4 Press i or e on the system repeatedly to set the minute for the timer to star t. 5 Press CLOCK•TIMER to store the star t time. . TIMER remains on the display. . At the preset time, the selected source will play. To exit without storing the setting . Press Con the system. Notes: – When the preset time is reached and the selected disc tray is empty, the next available disc will be selected. If all the disc trays are not available,Tuner will be selected automatically. – During timer setting, if no button is pressed within 90 seconds, the system will exit timer setting mode automatically. To deactivate the TIMER . Press TIMER ON/OFF on the remote control. . The display will show "OFF" and TIMER will disappear from the display. To activate the TIMER . Press TIMER ON/OFF on the remote control. . The last set timer information will be shown for a few seconds and TIMER will appear on the display. Sleep timer setting The sleep timer enables the system to switch to standby mode automatically at a preset time. 1 Press SLEEP on the remote control repeatedly to select a preset time. . The selections are as follows (time in minutes): 15 ™ 30 ™ 45 ™ 60 ™ OFF ™ 15 … . "SLEEP XX" or "OFF" is displayed. "XX" is the time in minutes. 2 When you reach the desired length of time, stop pressing the SLEEP button. . SLEEP is shown...