Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
••Risk of electric shock! When you unplug the AC power cord, always pull the plug from the socket. Never pull the cord. ••Before you connect the AC power cord, ensure that you have completed all other connections. 100-240 V~50/60 HzAC MAINS~ FMANTENNASPEAKER OUT (6) Demonstrate the features In the standby mode, you can demonstrate features by pressing . »»The features are displayed one by one across the display panel. • To turn off the demonstration, press again. English EN Prepare the remote control Caution ••Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. ••Risk of decreased battery life! Never mix different brands or types of batteries. ••Risk of product damage! When the remote control is not used for long periods, remove the batteries. To insert the remote control battery: 1 Open the battery compartment. 2 Insert the supplied AAA battery with correct polarity (+/-) as indicated. 3 Close the battery compartment. Set clock 1 In standby mode, press and hold CLOCK on the remote control for more than two seconds. »»[24H] or [12H] hour format is displayed. 2 Press / to select [24H] or [12H] hour format, and then press CLOCK. »»The hour digits are displayed and begin to blink. 3 Press / to set hour, and then press CLOCK. »»The minute digits are displayed and begin to blink. 4 Repeat step 3 to set minute. Note ••If no button is pressed in 90 seconds, the system exits clock setting mode automatically. Tip ••You can view clock information in power-on mode by pressing CLOCK. Turn on Press . »»The unit switches to the last selected source. Switch to standby mode Press again to switch the unit to standby mode. »»The clock (if set) is displayed on the panel. Switch to ECO standby mode: Press and hold for more than two seconds. »»The display panel is dimmed. Note ••The unit switches to Eco Power Standby mode after 15 minutes in standby mode. Switch between standby mode and ECO standby mode: Press and hold for more than two seconds. EN 4 Play Play from disc 1 Press CD to select CD source. 2 Press to open the disc compartment. 3 Insert a disc with the printed side facing upward. 4 Press to close the disc compartment. »»Play starts automatically. If not, press . AUDIO INPRESET/ALBUMMUTECLOCKSLEEPTIMERPROGSOUNDFMVOLSHUFFLECDREPEATDISPLAYRDSCDVOLUME Play from USB Note ••Make sure that the USB device contains playable audio content. 1 Press USB/AUDIO IN repeatedly to select the USB source. 2 Insert a USB device into the socket. »»Play starts automatically. If not, press . AUDIO INPRESET/ALBUMMUTECLOCKSLEEPTIMERPROGSOUNDFMVOLSHUFFLECDREPEATDISPLAYUSBVOLUMERDS Control play / Select a folder. / Select an audio file. Pause or resume play. Stop play. REPEAT Play a track or all tracks repeatedly. SHUFFLE Play tracks randomly. VOL +/- Increase or decrease the volume. MUTE Mute or restore sound. SOUND Enrich sound effect with DSC: balanced, clear, powerful, warm, and bright. DISPLAY Adjust display brightness. Skip to a track For CD: Press / to select another track. For MP3 disc and USB: 1 Press / to select an album or a folder. 2 Press / to select a track or a file. Program tracks You can program a maximum of 20 tracks. 1 Press PROG to activate the program mode. 2 For MP3 tracks, press / to select an album. 3 Press / to select a track, and then press PROG to confirm. 4 Repeat steps 2 to 3 to program more tracks. 5 Press to play the programmed tracks. »»During play, [PROG] (program) is displayed. • To erase the program, in the stop position, press . English EN 5 Listen to the radio Tune to a radio station Tip ••Position the antenna as far as possible from TV, VCR, or other radiation source. ••For optimal reception, fully extend and adjust the position of the antenna. 1 Press FM to select FM source. 2 Press and hold / for more than two seconds. »»The radio tunes to a station with strong reception automatically. 3 Repeat step 2 to tune to more stations. To tune to a weak station: Press / repeatedly until you find optimal reception. Program radio stations automatically Note ••You can program a maximum of 20 preset radio stations (FM). In tuner mode, press and hold PROG for more than two seconds to activate automatic programming. »»All available stations are programmed in the order of waveband reception strength. »»The first programmed radio station is broadcast automatically. Program radio stations manually 1 Tune to a radio station. 2 Press PROG, and then press / to select a number from 1–20. 3 Press PROG to confirm. »»The preset number and the frequency of the preset station are displayed. 4 Repeat steps 2-3 to program more stations. Note ••To overwrite a programmed station, store another station in its place. Select a preset radio station In tuner mode, press / to select a preset number. Show RDS information Radio Data System (RDS) is a service that allows FM stations to show additional information. If you tune to an RDS station, an RDS icon and the station name are displayed. 1 T...