Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
. "TUNER" is displayed. A few seconds later, the current radio frequency will appear on the display. 2 Press TUNER again to select the desired waveband : FM or MW. 3 Press and hold a or a until the frequency indication starts to change, then release. . The display will show "SEARCH" until a radio station with sufficient signal strength is found. 4 Repeat step 3 if necessary until you find the desired radio station. . To tune to a weak station, press a or a briefly and repeatedly until optimal reception found. Storing preset radio stations You can store up to 40 preset radio stations in the memory. Automatic Preset Programming 1 Press TUNER to select TUNER mode. To begin automatic preset from a desired preset number . Press i or e to select the desired preset number. . If a radio station has been stored in one of the presets, it will not be stored again under another preset number. 2 Press and hold PROGRAM until "AUTO" is displayed. . PROG starts flashing. . AUTO is displayed and available stations are programmed in order of waveband reception strength. The first preset automatically stored will then be played. . When all the available radio stations are stored or the memory for 40 presets are used, the last preset radio station will be played. To stop storing the automatic preset . Press PROGRAM or STOP 9 on the system. Note: – If no preset number is selected, automatic preset will begin from preset (1) and all your former presets will be overridden. y CD1/2/3 MUTE REPEAT PROGRAM SHUFFLE DSC DBB DISPLAY DIM SLEEP TITLE ALBUM TUNER AUX VOL MHz TIMER ON/OFF Manual Preset Programming Manual Preset Programming Radio Reception English 1 Tune to your desired radio station (refer to “Tuning to radio stations”). 2 Press PROGRAM. . PROG star ts flashing. . The next available preset number is displayed for selection. To store the radio station to another preset number . Press i or e to select the desired preset number. 3 Press PROGRAM again to store the radio station. . PROG disappears. . Repeat steps 1–3 to store other radio stations. To exit manual preset mode . Press STOP 9 on the system. Notes: – If you attempt to store more than 40 preset radio stations, "PROGRAM FULL" is displayed. – During programming, if no key is pressed within 25 seconds, the system will exit the programme mode automatically. Tuning to preset radio stations . Once you’ve programmed the radio stations, press i or e to select the desired preset number. . The preset number, radio frequency, and waveband are displayed. For Recording, please refer to “Tape Operation/Recording”. 19 20 English Tape Operation/Recording IMPORTANT! – Before playing a tape, check and tighten slack tape with a pencil. Slack tape may get jammed or may burst in the mechanism. – C-120 tape is extremely thin and is easily deformed or damaged. It is not recommended for use in this system. – Store the tapes at room temperature and do not put them too close to a magnetic field (for example, a transformer, TV or speaker). Tape playback 1 Select TAPE source. 2 Open the tape key flap marked “OPEN 2” on the front panel. 3 Press STOP•OPENC0 to open the tape door. 4 Insert a recorded tape and close the tape door. . Load the tape with the open side downward and the full spool to the left. 5 Press PLAY 2 to star t playback. . The key is automatically released at the end of a tape, except if PAUSE; has been activated. 6 To pause, press PAUSE;. Press again to resume. 7 By pressing a or a on the system fast winding of tape is possible in both directions. 8 To stop the tape, press STOP•OPENC0. Note: – The sound source cannot be changed while playing or recording a tape. Tape Operation/Recording English General information on recording . If you do not intend to record via the microphone, unplug the microphone to avoid accidental mixing with other recording source. . Recording is permissible insofar as copyright or other rights of third par ties are not infringed. . For recording, use only NORMAL (IEC type I) tapes on which the tabs have not yet been broken.This deck is not suited for recording on METAL (IEC IV) type tapes. . The recording level is set automatically, regardless of the position of the Volume, DBB, DSC and so for th. . The recording sound quality might differ depending on the quality of your recording source and the recording tape. . The tape is secured at both ends with leader tape. At the beginning and end of the tape, nothing will be recorded for six to seven seconds. . To protect a tape from accidental erasure, have the tape in front of you and break out the left tab. Recording on this side is no longer possible. If, however, you wish to record over this side again, cover the tabs with a piece of adhesive tape. Synchro start CD recording 1 Select CD source. 2 Insert a disc and if desired, programme track numbers. 3 Press STOP•OPENC0 to open the tape door. 4 Insert a suitable tape into the deck and close the tape door. 5 Press RECORD to star t recording. To select and rec...