Votos - 2, Puntuación media: 5
(
)
)
|
Fotos y especificaciones Sony MHC-RG590S |
Resumen del manual
4 Set the time to start playing or recording. Press ./. . repeatedly to set the hour, and then press ENTER .. The minute indication flashes. Use the procedure above to set the minutes. 5 Use the same procedure as in step 4 to set the time to stop playing or recording. 6 Select the sound source or prepare the tape. Play Timer Press ./. . repeatedly until the desired sound source appears, and then press ENTER .. The display shows the timer settings. Rec Timer Load a recordable tape into deck B. The display shows the timer settings. 7 Press ./. . to turn off the system. The system turns on 15 seconds before the preset time. If the system is on at the preset time, the Play Timer and the Rec Timer will not play or record. Continued . To activate or check the timer again Press CLOCK/TIMER SELECT ., press ./. . repeatedly until “PLAY SELECT” or “REC SELECT” appears, and then press ENTER .. To cancel the timer Repeat the same procedure as above until “TIMER OFF” appears, and then press ENTER .. To change the setting Start over from step 1. Tips • The Play Timer setting remains as long as the setting is not canceled manually. • The volume is reduced to minimum during the Rec Timer. • The Rec Timer is canceled automatically after the Rec Timer has been activated. 24GB Tape deck The sound exhibits excessive wow or flutter or dropout. • Clean the capstans and pinch rollers. Also, clean and demagnetize the tape heads. See “Precautions” for details (page 25). To change the AM tuning interval The AM tuning interval is factory-preset to 9 kHz (or 10 kHz, for some areas; this function is not available on the European, Russian and Saudi Arabian models). You cannot change the AM tuning interval in Power Saving Mode. Use buttons on the unit to change the AM tuning interval. 1 Tune in any AM station, and then turn off the system. 2 While holding down TUNING – ., press ./. .. All the AM preset stations are erased. To reset the interval to the factory preset, repeat the procedure. To improve tuner reception Turn off CD player power by using the CD power management function. By default, CD power is turned on. You cannot change the setting in Power Saving Mode. Use buttons on the unit to turn off CD player power. 1 Press CD . to select the CD function. 2 Press ./. . to turn off the system. 3 After “STANDBY” stops flashing, press ./. . while holding down . .. “CD POWER OFF” appears. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until “CD POWER ON” appears. To reset the system to factory settings If the system still does not operate properly, reset the system to factory settings. You cannot reset the system to factory settings in Power Saving Mode. Use buttons on the unit to reset the system to its factory default settings. 1 Disconnect and reconnect the power cord, and then turn on the system. 2 Press ., .. ., and DISC 1 . at the same time. All user-configured settings, such as preset radio stations, timer, and the clock, are deleted. MHC-RG490S Front speaker DIN power output (rated): 95 + 95 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 125 + 125 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference): 250 + 250 watts (6 ohms at 1 kHz, 10% THD) Subwoofer DIN power output (rated): 120 watts (6 ohms at 80 Hz, DIN) Continuous RMS power output (reference): 150 watts (6 ohms at 80 Hz, 10% THD) Music power output (reference): 300 watts (6 ohms at 80 Hz, 10% THD) MHC-RG290 DIN power output (rated): 90 + 90 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 120 + 120 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference): 240 + 240 watts (6 ohms at 1 kHz, 10% THD) MHC-RG190 DIN power output (rated): 40 + 40 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 50 + 50 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference): 100 + 100 watts (6 ohms at 1 kHz, 10% THD) Other models: MHC-RG490S Front speaker The following are measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 95 + 95 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 125 + 125 watts (6 ohms at 1 kHz, 10% THD) Subwoofer DIN power output (rated): 120 watts (6 ohms at 80 Hz, DIN) Continuous RMS power output (reference): 150 watts (6 ohms at 80 Hz, 10% THD) MHC-RG290 The following are measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 95 + 95 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 125 + 125 watts (6 ohms at 1 kHz, 10% THD) MHC-RG190 The following are measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 50 + 50 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 65 + 65 watts (6 ohms at 1 kHz, 10% THD) Inputs: AUDIO IN (stereo mini jack): voltage 250 mV, impedance 47 kilohms MIC (phone jack) (Latin American model only): sensitivity 1 mV, impedance 10 kilohms Outputs: PHONES (stereo mini jack): accepts headphon...
Otros modelos de este manual:estéreo - MHC-GX470 (960.15 kb)
estéreo - MHC-RG190 (960.15 kb)
estéreo - MHC-RG290 (960.15 kb)
estéreo - MHC-RG490S (960.15 kb)