Votos - 4, Puntuación media: 4.3
(
)
)
|
Fotos y especificaciones Sony MHC-EC55 |
Resumen del manual
Voltage selector For models with a voltage selector, set VOLTAGE SELECTOR to the local power line voltage. *Saudi Arabian model: 120 – 127 V/220 – 240 V/ NO OPERATION Other Operations General 1 Press CD on the remote (or FUNCTION repeatedly) .Discs that have labels printed using ink that feels tacky Power requirements: . to select the CD function. when touched Recording onto a tape (Except for North American model: AC 120 V, 60 Hz 2 Press .... to turn off the system. Specifications European and Russian models: AC 230 V, 50/60 Hz North American model) Troubleshooting Notes on discs Australian model: AC 230 – 240 V, 50/60 Hz Main unit 1 Make sure the power cord and speaker cords are Mexican model: AC 127 V, 60 Hz 3 After “STANDBY” stops flashing, press DISPLAY . .Before playing, wipe the disc with a cleaning cloth from AUDIO POWER SPECIFICATIONS Creating your own CD program Use a TYPE I (normal) tape only. correctly and firmly connected. Argentine model: AC 220 V, 50/60 Hz to display the clock and then press ....while the center out to the edge. POWER OUTPUT AND TOTAL HARMONIC DISTORTION: Korean model: AC 220 V, 60 Hz You can record just the portions you like from a sound holding down .. on the unit. (MHC-GX99, MHC-EC77 The United States model only) 2 Find your problem in the checklist below, and take .Do not clean discs with solvents, such as benzine Saudi Arabian model: AC 120 – 127, 220 – 240 V, 50/60 Hz, adjustable with Low channel (Program Play) source, including connected audio components. voltage selector the indicated corrective action. “CD POWER OFF” appears. With CD player power thinner, or commercially available cleaners or anti-With 8 ohm loads, both channels driven, from 120 – 10,000 Hz; 60 watts Other models: AC 120, 220 or 230 – 240 V, 50/60 Hz, adjustable with voltage Use buttons on the remote to create your own program. turned off, disc access time is increased. To turn on static spray intended for vinyl LPs. per channel minimum RMS power, with no more than 0.7% total harmonic selector Use buttons on the unit to control tape recording. If the issue persists, contact your nearest Sony dealer. distortion from 250 milliwatts to rated output. CD player power, repeat the procedure until “CD .Do not expose discs to direct sunlight or heat sources High channel Power consumption: 1 Press CD . to select the CD function. 1 Insert a recordable tape into the cassette holder POWER ON” appears. such as hot air ducts, nor leave it in a car parked in With 8 ohm loads, both channels driven, from 2,000 – 13,000 Hz; 60 watts MHC-GX99 If the STANDBY indicator flashes 2 Press PLAY MODE . repeatedly until “PGM” appears with the side you want to record facing up. per channel minimum RMS power, with no more than 0.7% total harmonic direct sunlight. USA model: 190 W distortion from 250 milliwatts to rated output. while the player is stopped. Immediately unplug the power cord, and check the Canadian model: 245 VA 2 Prepare the recording source. To reset the system to factory settings AUDIO POWER SPECIFICATIONS following item. On safety SA-WG99 (Subwoofer) 3 Press DISC SKIP . to select a disc. Select the desired source to record. POWER OUTPUT AND TOTAL HARMONIC DISTORTION: If the system still does not operate properly, reset the USA model: 115 W .If your system has a voltage selector, is the voltage .The unit is not disconnected from the AC power source (MHC-EC55 The United States model only) 4 Press ./.(or ./.on the unit) . Place the disc you want to record and press DISC system to factory settings. Canadian model: 155 VA With 6 ohm loads, both channels driven, from 120 – 10,000 Hz; 45 watts selector set to the correct voltage? (mains) as long as it is connected to the wall outlet, Use buttons on the unit to reset the unit to its factory per channel minimum RMS power, with no more than 0.7% total harmonic MHC-EC77 repeatedly until the desired track number appears. SKIP/EX-CHANGE . to select a disc. After the STANDBY indicator . on the unit stops even if the unit itself has been turned off. distortion from 250 milliwatts to rated output. USA model: 190 W default settings. When recording a folder from an MP3 disc, press flashing, reconnect the power cord, and turn on the When programing MP3 files, press +/– . .Completely disconnect the power cord (mains lead) Canadian model: 245 VA repeatedly to select the desired folder, and then select PLAY MODE . repeatedly to select “ ,” and then European and Russian models: 140 W system. If the issue persists, contact your nearest Sony 1 Disconnect and reconnect the power cord, and then from the wall socket (mains) if it is not going to be used Amplifier section 0.5 W (in Power Saving Mode) press +/– . repeatedly to select the desired dealer. the desired file. turn on the system. for an extended period of time. When unplugging the MHC-GX99 Other models: 150 W folder. unit, always grip the plug. Never pull the cord itself. Front speaker: 2 Press PLAY MODE ., FUNCTION ., and .... at ...
Otros modelos de este manual:estéreo - MHC-EC77 (724.78 kb)
estéreo - MHC-GX99 (724.78 kb)