Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Starting playback takes more time than usual. .The following discs take a longer time to start playback. .a disc recorded with a complicated tree structure. .a disc recorded in multisession mode. .a disc that has not been finalized (a disc to which data can be added). .a disc that has many folders. USB device Are you using a supported USB device? .If you connect an unsupported USB device, the following problems may occur. See “Playable USB devices” (page 29) for the supported device types. .The USB device is not recognized. .File or folder names are not displayed on this system. .Playback is not possible. .The sound skips. .There is noise. “Over Current” appears. .A problem has been detected with the level of electrical current from the (USB) port .. Turn off the system and remove the USB device from the (USB) port .. Make sure there is no problem with the USB device. If this display pattern persists, contact your nearest Sony dealer. There is no sound. .The USB device is not connected correctly. Turn off the system, then reconnect the USB device and check if the USB MEMORY indicator . lights up. The sound is distorted. .The bit rate used when encoding the files was low. Send files encoded with higher bit rates to the USB device. There is noise or the sound skips. .Turn off the system, then reconnect the USB device. .The music data itself contains noise. Noise may have been introduced when creating music data due to the conditions of the computer. Create the music data again. .When using the USB storage media, copy the files to your computer, format the USB storage media in FAT16 or FAT32 format, and copy the files to the USB storage media again.* The USB device cannot be connected into the (USB) port .. .The USB device is being connected backwards. Connect the USB device in the correct orientation. The USB storage media which has been used on another device does not work. .It may be recorded in an unsupported format. If so, first take the precaution of backing up important files on the USB storage media by copying them to your computer hard disk. Next, format the USB storage media with a FAT16 or FAT32 file system and transfer the backed-up audio files onto the USB storage media again.* Others Continued . GB “Reading” is displayed for a long time. .It may take a while to finish reading the USB device if there are many folders or files on it. Thus, we recommend following these guidelines. .Total folders on USB device: 100 or less .Total files per folder: 100 or less Erroneous display .Send the music data to the USB device again, as the data stored in the USB device may have been corrupted. Play does not start. .Turn off the system, then reconnect the USB device. .Connect the USB device that this system can play. .Press . (or USB .. on the unit) . to start play. Play does not start from the first track. .Set the play mode to Normal Play mode. Files cannot be played back. .USB storage media formatted with file systems other than FAT16 or FAT32 are unsupported.* .If you use partitioned USB storage media, only files on the first partition can be played. .Files that are encrypted or protected by passwords, etc. cannot be played back. * This system supports FAT16 and FAT32, but some USB storage media may not support all of these FAT. For details, see the operation manual of each USB storage media or contact the manufacturer. Tuner Severe hum or noise, or stations cannot be received. (“TUNED” or “ST” flashes on the display.) .Connect the antenna properly. .Find a location and an orientation that provide good reception, and then set up the antenna again. .Keep the antennas away from the speaker cords, the power cord and the USB cable to avoid picking up noise. .Connect a commercially available external antenna. .Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand. .Turn off nearby electrical equipment. To change the AM tuning interval The AM tuning interval is factory-preset to 9 kHz (or 10 kHz, for some areas; this function is not available on the European model). Use buttons on the unit to change the AM tuning interval. 1 Tune in any AM station, and then turn off the system. 2 While holding down TUNER/BAND ., press ./... All the AM preset stations are erased. To reset the interval to the factory preset, repeat the procedure. GB To improve tuner reception Turn off CD player power by using the CD power management function. By default, CD power is turned on. 1 Press FUNCTION . repeatedly to select the CD function, and then turn off the system. 2 After “STANDBY” stops flashing, press ./..on the unit while holding down ./CANCEL . on the unit. “CD POWER OFF” appears. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until “CD POWER ON” appears. To reset the system to factory settings If the system still does not operate properly, reset the system to factory settings. Use buttons on the unit to reset the system to its f...
Otros modelos de este manual:estéreo - CMT-HX3 (569.28 kb)