Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
2 Turn the jog dial to set the hour. continued Step 2: Setting the time (coninued) 3 Press ENTER/NEXT. The minute indication flashes. 4 Turn the jog dial to set the minute. 5 Press ENTER/NEXT. The clock starts working. Tip If you’ve made a mistake, start over from step 1. To change the time The previous explanation shows you how to set the time while the power is off. To change the time while the power is on, do the following: 1 Press CLOCK/TIMER SET. 2 Turn the jog dial to select SET CLOCK. 3 Press ENTER/NEXT. 4 Perform steps 2 through 5 above. Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs. Step 3: Presetting radio stations You can preset the following number of stations: – 2 band model: 20 for FM, 10 for AM. – 3 band model: 20 for FM, 10 for MW, and 10 for SW, or 20 for FM, 10 for AM and 5 for UKV, depending on the model you purchased. (Power) Jog dial 4 32 1 Press TUNER/BAND repeatedly until the band you want appears in the display. The bands you can receive vary depending on the model you purchased. Be sure to check which bands you can receive. Every time you press this button, the band changes as follows: 2 band model: FM .AM 3 band model: To tune in a station with a weak signal Press + or – repeatedly in step 2 to tune in the station manually. To set another station to the exist preset number Start over from step 1. After step 3, turn the jog dial to select the preset number you want to store the other station. You can add a new preset number after the last preset number. FM nMW nSW To erase a preset station n 1 Keep pressing TUNER MEMORY until a or preset number appears in the display. FM nAM nUKV* n * “STEREO PLUS” is displayed when you select UKV. 2 Press and hold + or – until the frequency indication starts to change, then release. Scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. 3 Press TUNER MEMORY. A preset number appears in the display. The stations are stored from preset number 1. Preset number 4 Press ENTER/NEXT. The station is stored. 5 Repeat steps 1 to 4 to store other stations. 2 Turn the jog dial to select the preset number you want to erase. Select “ALL ERASE” when you want to erase all the preset stations. 3 Press ENTER/NEXT. “COMPLETE” appears. When you erase a preset number, the preset number decreases by one and all preset numbers following the erased one are renumbered. To change the AM tuning interval (Except for the European and Middle Eastern models) The AM tuning interval is factory set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER/NEXT button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure. Tip The preset stations are retained for half a day even if you unplug the power cord or if a power failure occurs. Saving the power in standby mode (For MHC-RXD9/RXD80/RXD7/R770) You can lower the power consumption to a minimum (Power Saving Mode) and save energy in the standby mode. POWER SAVE /DEMO (Power) DISPLAY Tips • Each time you press POWER SAVE/DEMO in the Power Saving Mode, the display switches between the Power Saving Mode and the demo mode. • indicator and timer indicator (when the timer is set) light up even in the Power Saving Mode. • The timer works in the Power Saving Mode. Notes • You cannot set the time in the Power Saving Mode. • One Touch Play function does not work in the Power Saving Mode. To cancel the Power Saving Mode Press DISPLAY. The clock display appears. /Press POWER SAVE/DEMO when the power is off. The system switches to the Power Saving Mode and the clock display disappears. The system is powering on/off by pressing . Basic Operations Basic Operations Playing a CD — Normal play You can play up to three CDs in a row. DISC SKIP/ EX-CHANGE CD (Pp2 1(Power) PLAY =+ 0) VOLUME MODE A . CD ( P p =+ 0) VOL +/– 1 Press ¤and place up to two CDs on the disc tray. If a disc is not placed properly it will not be recognized. With the label side up. When you play a single CD, place it on the inner circle of the tray. To insert a third disc, press DISC SKIP/ EX-CHANGE to rotate the disc tray. 2 Press one of the DISC 1~3 buttons. The disc tray closes and play starts. If you press CD (P(or CD (on the remote) when the disc tray is closed, play starts from the CD loaded on the tray whose button is lit green. Track number Playing time Basic Operations Disc tray number continued Playing a CD (continued) Tips To Do this Stop play Press p. Pause Press CD (P(Pon the remote). Press again to resume play. Select a track During play or pause, turn the jog dial clockwise (to go forward) or counterclockwise (to go back) and release it when you reach the desired track. (Or press +(to go forward) or =(to go back) on the remote.) Find a point in Press and hold down )or a track 0during play a...
Otros modelos de este manual:estéreo - MHC-GRX50 (723.43 kb)
estéreo - MHC-GRX70J (723.43 kb)
estéreo - MHC-GRX9900 (723.43 kb)
estéreo - MHC-R770 (723.43 kb)