Votos - 1, Puntuación media: 3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
.Erase the pairing registration information of a Bluetooth device and perform the pairing operation Prepare the sound source, and then press VOLUME Frequency response: 20 Hz . 20 kHz .. 1 Prepare the sound source. .Install a noise filter (not supplied) to the power cord. again. beep to confirm key-touch while the Dock indicator with a mild detergent solution. Do not use any type of Signal-to-noise ratio: More than 90 dB +/.. to adjust the volume. is flashing, although operation of the touch panel is abrasive pads, scouring powder, or solvents, such as Dynamic range: More than 90 dB 3 Press Connect additional audio component to the AUDIO “COMPLETE” appears and all the pairing To start from a specific CD track, audio file, and The remote does not function. The sound skips or fluctuates, or the enabled even while the Dock indicator is flashing. thinner, benzine, or alcohol. Tuner section IN jack . on the unit using an audio analog cord information is erased. radio station create your own program. .Remove any obstacles between the remote and the FM stereo, FM superheterodyne tuner connection is lost. (not supplied). remote sensor . on the unit, and position the unit Antenna: FM lead antenna Notes 2 Select the timer set mode. .The system and the Bluetooth device are too far apart. Tuning range: .If you erase the pairing information, you cannot make a Bluetooth 2 Turn down the volume. away from fluorescent lights. 87.5 MHz . 108.0 MHz (50 kHz step) .If there are obstacles between the system and your connection unless pairing is performed. In order to connect with Press and hold SHIFT . and TIMER MENU .. .Point the remote at the system’s sensor .. Press VOLUME ... DAB/DAB+ tuner section: Bluetooth device, remove or avoid the obstacles. a Bluetooth device after performing this operation, you must enter FM stereo, DAB/FM superheterodyne tuner 3 Set the play timer. .Move the remote closer to the system. the passkey again. 3 Select the AUDIO IN function. .If there is equipment that generates electromagnetic Messages Bluetooth wireless technology Frequency range* .If you erase the pairing information, the Bluetooth Standby mode Press ./.. repeatedly to select “PLAY SET,” then radiation, such as a wireless LAN, other Bluetooth CAN’T PLAY : You have inserted a disc that cannot be Bluetooth wireless technology is a short-range wireless Band-III: 174.928 (5A) MHz . 239.200 (13F) MHz Press AUDIO IN FUNCTION . on the remote or .. The STANDBY indicator . remains lit after * For details, see “DAB/DAB+ frequency table” below. setting is set to off. press device, or a microwave oven nearby, move them away. played back on this system. technology linking digital devices, such as personal press FUNCTION . on the unit repeatedly. unplugging the power cord. Antenna: DAB/FM lead antenna 4 Set the time to start playback. COMPLETE : The preset operation ended normally. computers and digital still cameras. Using the Bluetooth The DAB/DAB+ services are available only in countries/regions that The function indicator lights in amber. .The STANDBY indicator . may not turn off The sound of your Bluetooth device cannot be support DAB/DAB+ services. Playing music from a Bluetooth device wireless technology, you can operate the units involved ERROR : Unpredictable situations or an unknown device Press ./.. repeatedly to set the hour, then press immediately after unplugging the power cord. The heard on this system. 4 Start playback. You can operate a Bluetooth device by connecting the is connected. within a range of about 10 meters. DAB/DAB+ frequency table (Band-III) .. Use the procedure above to set the minutes. indicator will turn off after about 40 seconds. This is system and a Bluetooth device using AVRCP. Start playback of the connected component and .Turn up the volume on your Bluetooth device first, The Bluetooth wireless technology is commonly FULL : You tried to program more than 25 tracks or files not a malfunction. Frequency Label 5 Use the same procedure as in step 4 to set the time and then adjust the volume using VOLUME +/... Check the following before playing music: adjust the volume. (steps). used between two devices, but a single device can be 209.936 MHz 10A to stop playback. .The Bluetooth function of the Bluetooth device is enabled. connected to multiple devices. LOCKED : The disc slot does not work. Contact your 211.648 MHz 10B The system may enter Standby mode automatically if the volume 6 Select the sound source. nearest Sony dealer. You do not need wires to get connected as you do with .Pairing has been completed. Note CD/MP3 disc Severe hum or noise .If there are obstacles between the system and your 213.360 MHz 10C 1 Select the BLUETOOTH function. level of the connected component is too low. Adjust the component’s a USB connection, and you do not need to place the Press ./.. repeatedly until the desired sound The system does not eject the disc and Bluetooth device, remove or avoid the obstacles. NO DISC : There is no di...