Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Prepare screws and bracket. Unit Screws and Wall Plugs are not supplied for mounting the unit. We recommend the Hilti (HUD-1 6 x 30) for the mounting. , Note Wall Mount Bracket Wall bracket Installation Template 1. Match the T V’s BOTTOM EDGE of Wall Mount Bracket Installation Template with the bottom of T V and attach to the position. TV 2. When you mount it on a wall (concrete), use the wall plugs (Not supplied). You should drill some holes. A guide sheet ( Wall Mount Bracket Installation Template) is supplied to drill. Use the sheet to check the point to drill. Wall Mount Bracket Installation Template 1 Getting Started 10 Getting Started 1 3. Remove the Wall Mount Bracket Installation 5. Hang the main unit onto the bracket as shown Template. below. 4. Fix it with screws (not supplied) as shown in the illustration below. Getting Started >Caution • Do not install this unit upside down. It can damage the parts of this unit or be the cause of personal injury. • Do not hang onto the installed unit and avoid any impact to the unit. • Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may result in an injury of a person or damage to the product. • When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall. Detach the unit from the bracket as shown below. , Note Connecting 11 1111 Speaker Connection Pairing wireless subwoofer LED indicator of wireless subwoofer LED Color Status Yellow-green The wireless subwoofer is , Note • If there is a strong electromagnetic wave product nearby, interference may occur. Put the unit (Wireless subwoofer and main unit) away from there. • If you operate main unit then wireless subwoofer sound within a few seconds in standby mode. • Set the distance between this unit and subwoofer Receiver within 10 m (32 ft.). 2 receiving the signal of the unit. Yellow-green The wireless subwoofer is trying (blink) to connect. Red The Wireless subwoofer is in standby mode. Off (No The power cord of wireless display) subwoofer is disconnected. Setting up the wireless subwoofer for the first time 1. Connect the power cord of the Wireless subwoofer to the outlet. 2. Turn on the main unit : The main unit and wireless subwoofer will be automatically connected. Manually pairing wireless subwoofer When your connection is not completed, you can see the red LED on the woofer and woofer is not made sound. To solve the problem, follow the below steps. 1. Press and hold Z (Stop) button on the unit and MUTE button on the remote control simultaneously. -Displays the “REMATE”. 2. Press PAIRING on back of the woofer. -The Yellow-green LED will flicker. 3. Turn off and on the unit. -If you see “Yellow-green” LED, it’ s successful. 4. If you don’t see “Yellow-green” LED, try again Step 1 - Step 3. • Optimum performance can be implemented only when the unit and the Wireless subwoofer within distance of 2 m (6 ft.) to 10 m (32 ft.) is used since communication failure may occur if longer distance is used. • It takes a few seconds (and may take longer) for the Wireless Transmitter and subwoofer to communicate with each other. Connecting 12 Connecting 2 Connecting to Your TV HDMI Connection If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable ( Type A, High speed HDMI™ cable with Ethernet). Connect the HDMI jack on the unit to the HDMI jack on a HDMI compatible TV or monitor. Connecting TV HDMI cable Set the TV’s source to HDMI (refer to TV’s Owner’s manual). Additional Information for HDMI • When you connect a HDMI or DVI compatible device, make sure of the followings: -Try switching off the HDMI/DVI device and this unit. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this unit. -The connected device’s video input is set correctly for this unit. - The connected device is compatible with 720 x 576p, 1280 x 720p, 1920 x 1080i or 1920 x 1080p video input. • Not all HDCP-compatible HDMI or DVI devices will work with this unit. - The picture will not be displayed properly with non-HDCP device. , Note • If a connected HDMI device does not accept the audio output of the unit, the HDMI device’s audio sound may be distorted or may not output. • When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution Setting” on page 14 ) • Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Settings] menu (see page 18). • Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, restart the unit. • When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable. • If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m(15 ft.)). Connecting 13 What is SIMPLIN...