Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
INTRODUCTION Congratulations on your purchase of the MD-20 CD turntable and welcome to the KRELL family of audio components. You have joined a select group of listeners who enjoy only the finest in music reproduction. We are dedicated to the~ development of technologicallyadvanced components tor the reproduction o,f diglt~ly recorded music and continuing the Krell tradition ot uncompromised performance through leading-edge teclanology. This Owner’s Reference is divided into several sections, each designed to perform a different function. Basicinstallation, operation and a Question and Answer section are included, where answers to commonquestions are provided. Should you have any questions or suggestipns, i~lease feel free to contact your authorized dealer or tlaeKRELL for assistance. staff In the unlikely, event that your.MD-20 should require service you will be pleased~ to ~now that it is backed by ac.omprehensive Customer batistaction policy and one of toe most advanced servic.e facilities in the industry. Fordetailed information on the terms and conditions of service please consult your warra,nty registration card or your authorized KRELL Distributor. 2 B. TABLE OF CONTENTS 3 UNPACKING AND ASSEMBLY 4 CUSTOM DUST COVER INSTALLATION 6 BASIC INSTALLATION AND CONNECTIONS 8 OPERATION OF THE CD TRANSPORT 10 REMOTE CONTROL 11 TRACK AND FTS PROGRAMMING 15 MAINTENANCE 16 QUESTIONS AND ANSWERS 18 SPECIFICATIONS 19 WARRANTY AND SERVICE INFORMATION C. UNPACKING AND ASSEMBLY 1. Open the box and remove the top layer of protectivefoam. The following items will now be visibIe: 1 CD Stabilizer 1 AC power cord 1 MD-20RC Remote Control 1 Packet containing the Owner’s Reference and warrantycard NOTE:If any of these items are not included, pleasecontact your authorized dealer immediately f6r assistance. 2. Removethe layer of foam containing these items and set it aside for later use. Carefully remove the MD-20 from its box and remove the protective plastic wrap. NOTE:Save all packing mate.rials. If you must ship your MD-20in the future, repack tlae unit in its original pa.ck aging to prevent transit damage. If the unit is returnecl to KRELLfor service, please send the cover and the remote control unit. CAUTION:If your MD-20 has the Custom cover do not remove the acrylic dust cover from its protective sleeve at this time! This cover is extremely delicate and c.an bepermanently scarred if mishandled. Please follow tlae 1.nstructions provided in this Reference after safe installation. 3 D. CUSTOM DUST COVER INSTALLATION 1. Standard Version Smoked Top Cover: Removethe top cover, in its protective sleeve, from thes.hipping foam. To prevent s.c.ra.tching, leave tlae protectivesl.eeve on tlae top cover until t~lae cover mounting is complete. T.here are two pairs ot screws .with w~asher-typereceptacles attached to t-he back panel of the unit tor mount- i.ng the top cover. Center the hinge pins on the top cover ov.ertoe two pairs of screws. Carefully slide the hinges into tlae.slots formed by the washers. Pusti the cover down evenly on both sides until it is fully seated. Finally, remove the protective sleeve. 2. Custom Version Clear Lucite Top Cover: Remove the top cover from the protective foam and its protective sleeve. Th. ere are two pairs of.screws with washer- type lainge receptacl.es on the ba.ck of tlae unit. Remove the four screws from tlae unit and take off the black .hin.ge receptacles. Carefully place the lucite top cover sucla tlaatthe circular milled-out portion is centered over the transport. Align the slots in the cover’s hinge blocks with theholes in the back of the chassis. Thread the four screws into the chassis t.hrough the hinge blocks: Tigh. ten dow~n light.lyand adjust the cover so it is centerec~ on the unit. Once the cover as aligned, tighten down the supporting screws. NOTE:The clear lucite cover must be lowered manually, as it is very heavy and does not have a damping mechanism. 4 INSTALLATION OF THE CUSTOM ACRYLIC DUSTCOVER FOR MD-20 REMOVEABLE MOLDED COVER MD-20 MADE IN U.S.A. NO U~ER PARTS XLR SERVICEABLEINSIDE SPECIAL O 1. To remove molded cover, slide the cover assembly upward until the hinges are cleared from both sets of screws and washers. 2. Be sure to save all the screws and washers after disassembly. CUSTOM ACRYLIC COVER E PARTS INSIDE ~ ~ SPECIAL 1. Removethe four original hinge retaining screws from the back of the unit. 2. Remove the three washers from each screw. 3. Gently place acrylic cover on the chassis top, center the hinges to match the holes in the chassis. 4. Insert the four screws without washers into the hinge and fasten loosely. 5. Center the cover with the chassis and secure hinge block screws. SEPT.EMBER1, 1992 E. BASIC INSTALLATION AND CONNECTIONS 1. Place the unit on a clean, level surface away from excessive heat, moist,ure or light. Ideally, the MD-20should be placed on tlae top of an audio component cabinet or other "open air" rigid platform. 2. The MD-20 may. be. placed in...