Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
If you are connecting any additional gear that is not included in the CLUB-8800, refer to the appropriate manuals for detailed instructions. Gathering Package Contents The first step to putting together your new CLUB system is unpacking all of the necessary equipment. Remember to keep your manuals nearby when setting up, as you may need to reference them. The products listed below are included in the CLUB-8800 system: CDG-9000PRO VX-15 Speakers Road Case • (2) RCA cables • (4) VX-15 speakers • (1) CLUB-8 road case • (2) Control interface connector UHF-5800 • (1) Rolling cart wires • (1) 3 ft. male/male .” cable • (2) MK 38PRO microphones • (1) Instruction manual VSP-M1 Multi-Effect Digital Signal • (1) Gooseneck DJ light KJM-7800PRO Processor/Mixer • (1) Double RCA to .” cable (3’3”) • (1) Instruction manual • (1) Instruction manual • Rack-mounting screws VP-2100PRO SS-88 Speaker Stand • (1) Instruction manual • (4) SS-88 speaker stands Mounting components into the CLUB-8800 Follow these basic guidelines when mounting: Below is one way to configure your CLUB-8800: • Always screw in the mounting screws using an “X” formation. • If possible, to keep the products cooler, leave some space in between the components in the rack. CDG 9000 PRO CONTROLLER UHF 5800 VSP M1 KJ 7800 PRO CDG 9000 PRO PLAYER VP 2100 On the web at or call toll free 1-800-678-5348 Setup each SS-88 speaker stand by extending the support lefts to a position that is stable and tighten the tension mechanism firmly. Place a VX-15 speaker on top of the SS-88 so that the shaft of the SS-88 fits flush into the mounting cavity on the bottom of the VX-15. NOTE: Each end of the SS-88 pole has a particular diameter fitted for common speakers’ mounting cavities. If the SS-88 shaft does NOT fit flush into the mounting cavity on the VX-15, loosen the SS- 88 pole and reverse it in the stand and then remount the speaker. Repeat the above steps for each speaker and stand. Be sure that each product has a power cord firmly attached. It is recommended that you use a power strip/surge protector when connecting your CLUB-8800 to a power outlet. Connecting Power Setting up the speakers and speaker stands VX-15 Speaker SS-88 Stand Once you have mounted all of the components into the CLUB-8800, it is time to connect them. Follow these directions on connecting the components. NOTE: If you are also connecting components that are not part of the CLUB- 8800 system, please refer to the manual of that product for setup instructions. Connect the Control Interface Connector from the corresponding “CONNECT TO MAIN UNIT” jack on the rear panel of the remote unit to the “CONNECT TO REMOTE CONTROL” jack on the rear panel of the player unit. CDG-9000PRO remote unit to the player unit. Connecting the components CDG 9000 Player CDG 9000 Controller 1 1. 2. 3. MAKE SURE ALL PRODUCTS ARE POWERED OFF PRIOR TO CONNECTING TO AN AC OUTLET. Using the paired 3’3” RCA to .” cable (included): 1. Connect the RCA ends to the L/R unbalanced master outputs labeled UNBAL on the rear panel of the KJ-7800PRO. 2. Connect the .” ends to the CHANNEL 1 and CHANNEL 2 .” inputs on the rear panel of the VP-2100. You have the option of either connecting each deck of the CDG-9000PRO separately (Fig. 1) or together through a single SWITCHED output (Fig. 2). KJ-7800PRO to VP-2100PRO CDG-9000PRO player unit to KJ-7800PRO remote key control remote key control Separately through individual deck outputs (Fig.1) Using RCA cables: 1. For each deck, connect the L/R (red & white) audio outputs and Video (yellow) output on the CDG-9000PRO to the AV1 and AV2 inputs on the rear panel of the KJ-7800PRO Together through SWITCHED output (Fig. 2) Using RCA cables: 1. Connect the L/R SWITCHED audio and SWITCHED video outputs on the CDG-9000PRO player to the AV1 audio input on the KJ-7800PRO. remote key control .............................. .............. ................ .............. .............. ........ ........ .............................. -BRIDGE+ ...................................... ............ ........ ............ .... ...... ........ ........ remote key control CDG 9000 Player KJ 7800 CDG 9000 Player KJ 7800 VP 2100 KJ 7800 2 3 remote key control You can either run the UHF-5800 mics through the VSP-M1 or go straight into the KJ-7800PRO mixer. Using either a pair of XLR(f) to XLR(m) or XLR(f) to .” cables: 1. Connect the XLR(f) end to the LEFT BALANCED OUPUT on the rear panel of the VSP-M1. 2. Now connect the XLR(m) or .” end to MIC input 1 on the front of the KJ-7800PRO. 3. Follow the above steps, now going from the RIGHT BALANCED OUPUT on the VSP-M1 to MIC input 2 on the front of the KJ-7800PRO. .............................. .............. ................ .............. .............. ........ ........ .............................. -BRIDGE+ ...................................... ............ ........ ............ .... ...... ........ ........ VX-15 Speaker #1 VX-15 Speaker #2 VX-15 Speak...