Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
4. AUX CONTROLS - The AUX knobs control the signal level that the channel sends to AUX bus. 5. PRE/POST BUTTON - This button determines if the AUX signal is Pre Fader (signal level is not affected by fader position) or Post Fader (signnal level is affected by the fader position). 6. EFX CONTROL - These knobs control the signal levels sent to the EFX bus. The channel signals mixed by this bus have their overall level set by the MASTER EFX SEND control to the EFX jack located on the front top panel. Since the control is place after the channel fader, the signal level will be affected by the channel fader’s setting. NOTE: The Effect bus signal is also fed into the internal DSP (digital signal processor). CONTROLMAX. BOOST/CUTFREQUENCYTYPEHIGH±15dB12kHzShelvingMID±12dB2.5kHzPeakingLOW±15dB80HzShelving ©American Audio® - - M1624FX Instruction Manual Page 9 7. PAN/BALANCE CONTROL - PAN (Mono Control) - This control pans the channel signal across the master L and R buses, therefore determining the ideal position of the sound from that channel. EXAMPLE: If the PAN control is set all the way to the left, the sound from that channel will only be projected from the left speaker only. Same goes for the control being set all the way to the right, only from the right speaker. BALANCE (Stereo Control) - This control lets you adjust the balance of the L/R position, of the stereo input signal. Turning this knob to the left moves the source signal towards the MAIN MIX L bus, turning the knob to the right sends the signal towards the MAIN MIX R bus. 8. MUTE/ALT 3/4 BUTTON - When the corresponding channels MUTE/ALT 3/4 button is not active (depressed) the channel output will be sent to the ALT 3/4 output, and not the MAIN L/R output. The ALT 3/4 bus gives you a second independent stereo sub mix with its own sub master stereo fader. 9. PFL BUTTONS - This button allows you to monitor the PRE FADER LEVEL input signal through headphones or the control room outputs. When the button is NOT pressed the channel signal will be sent to the PFL bus. 10. CHANNEL FADERS - Thes faders are channel’s main level control. These fader’s control the signal level sent from the channel to the master mixing, group outs, and effect buses. The settings of the input channel faders affect the mix or the sound level balance between the instruments or other sources connected to the inputs. When a channel is not being used, the fader should be set at the minimum position to prevent any unwanted noise added to the main signal. M1624FX channel controls and functions cont. ©American Audio® - - M1624FX Instruction Manual Page 10 M1624FX main controls and functions MAIN CONTROL SECTION 11 21 22 12 13 14 23 Effects List 15 24 16 25 17 26 18 19 27 20 ©American Audio® - - M1624FX Instruction Manual Page 11 M1624FX main controls and functions cont. MAIN CONTROL SECTION: 11. DSP PROGRAM DISPLAY - This displays shows the number of the selected effect. Please see the effect list located on the MAIN CONTROL SECTION of the mixing console. 12. DSP PROGRAM SELECT KNOB - The program knob wil allow you to select one of the 100 built-in digital effects. This control board has a 24 Bit digital high quality effect processor. 13. AUX PRE CONTROL - Use this control to adjust the signal level sent from the internal digital effect to the AUX bus. 14. stereo return control - Use the corresponding control knobs to adjust the signal level of the mixed L/R signal sent from the RETURN jack (L & R MONO) to the AUX bus. 15. MASTER SEND CONTROLS - AUX CONTROL KNOBS - Use this control knob to adjust the signal level sent to the AUX output jack. MASTER EFFECT CONTROLS - Use this knob to adjust the signal level of the EFFECT bus sent to the EFFECT output jack. 16. TAPE IN CONTROL - This knob controls the playback signal level from the component that is connected to the TAPE IN RCA JACKS located on at the top panel of the mixing board. 17. DSP ON/OFF BUTTON - This button turns the internal effect program on/off. 18. PFL BUTTON - Pressing this button “In” will allow you to send the effect signal to the PFL bus. 19. EFX RTN FADER - With this fader you can adjust the signal level sent from the digital effect to the MAIN bus. 20. alt 3/4 fader - With this fader you can adjust the final combined stereo signal level that is sent to the ALT 3/4 output jacks. 21. POWER INDICATOR - This indicator will light when mixer power switch is turned on. 22. PHANTOM POWER BUTTON - When this button is pressed “In”, the mixer will supply power to all channels the provide XLR MIC input jacks. Use this function when using one or more condensor microphones. Note: When this function is active, the mixer supplies DC +48V power to pins 2 and 3 of all XLR type MIC input jacks. • Leave this switch off if you do not need phantom power. • When you turn this function on, make sure that only condenser MICs are connected to the XLR input jacks. Devices other then ...