Channel grouping By setting the group assign switch (1-2 or 3- 4) of a channel to ON, the channel signal is sent to group busses 1 and 2 or 3 and 4. A group buss signal is output from the [GROUP OUT] jacks. When the [ASSIGN TO STEREO OUT] switch above the group fader is set to ON, the group buss signal is output to the corresponding stereo buss. For example, it would be a good idea to assign channels for drums to a group. You can control the level of drums using the corresponding group fader without altering the balance. ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ST 1-2 3-4 ASSIGN TO STEREO OUT GROUP 3, 4 ASSIGN TO STEREO OUT GROUP 1, 2 STEREO STEREO BUS GROUP 1-2 BUS GROUP 3-4 BUS Channels which are assigned to the stereo buss Channels which are assigned to the group busses Assigned to the stereo buss • Solo monitor By setting the [SOLO] switch(es) to ON ( ), you can solo monitor the corresponding channel signal(s). If at least one of the [SOLO] switches is set to ON, the [SOLO] indicator slowly flashes. : If any of the [SOLO] switches is set to ON, the solo signal is monitored, while the signal selected by the [MONITOR SELECT] switch is interrupted. You can find the [SOLO] switches on channels 1 through 16, the effect send, and AUX sends 1 through 3 (see below). [SOLO] indicator [SOLO] switches [SOLO] switches 34 Model LM16 [Mixer basics] You can connect a stereo audio source such as a CD player, MD player, etc., to the [SUB IN (L, R)] jacks and output it from the mixer’s output. Therefore, you can connect a BGM source and play it back during a break in the show, etc. Using SUB IN [SUB IN] control Audio player By setting the [SOURCE] switches on input channels 15 and 16 to the "SUB IN" position ( ), the signals from the [SUB IN] jacks are sent to these channels (L for channel 15, R for channel 16). Use the [SUB IN] control to adjust the input level. (Note that the [TRIM] control on each of channels 15 and 16 does not affect the [SUB IN] signal.) The following shows the setting example for playing back the signals from the [SUB IN] jacks by the main speakers of a live stage. 1 2 3 4 5 6 (1) Set the [SOURCE] switches on channels 15 and 16 to "TRK" ( ). The input signals from the [SUB IN] jacks are selected as the sources of channels 15 and 16. (2) Use the [SUB IN] control to adjust the level of the signals from the [SUB IN] jacks. You can use the [SUB IN] control to adjust the level of the signals from the [SUB IN] jacks, but cannot use the [TRIM] control for them. (3) To output the signals from the [SUB IN] jacks in stereo, set the [PAN] control on channel 15 to “L” and set the [PAN] control on channel 16 to “R”. (4) Set the [ST] assign switches on channels 15 and 16 to "ON" ( ). The signal from the [SUB IN] jacks is routed to the stereo L/R buss. (5) Use the channel faders on channel 15 and 16 to control the output level of the channel signals sent to the stereo L/R buss. (6) Use the [STEREO] faders on channels 15 and 16 to control the level of the stereo buss signal output from the [STEREO OUT (L, R)] connectors, which affects the main speaker volume. : The [SUB IN] jacks can be used to increase the total number of inputs by connecting to a sub mixer. Model LM16 [Mixer basics] Block diagram ST GROUP AUX PHONES MONITOR OUT(-12dBV) 35 BA SUB IN A/D SOLO - ° ~ +20dB (-10dBV) BABA GND - ° ~ +10dBFDRFDR - ° ~ +10dBFDRFDRGROUP3GROUP4 FDRGROUP2 TO ST FDRGROUP1 MONITOR SW LR/12/34/EFF - ° ~ +10dBEFF RTN L-R EFFECTEFF SENDAUX SEND3 AUX SEND2 AUX SEND1 - ° ~ +10dB DADA AUX SEND1BAMONITOR VOL AUX SEND2AUX SEND3EFF SEND(-2dBu) L R 1 2 3 4 1 2 3 EFF SOLO SOLOSOLOSOLOSOLO LEVELL R PHONES VOL DA SOLO 2 1 BA RLGROUP OUT(+4dBu) DADADA L3BAR1BA24BABABABA DA STEREO OUT (+4dBu) BABA ST MIX OUT(-10dBV) 1 2 3 4 1 2 3 4GROUP1-2 ON/OFF1 2 3 4GROUP3-4 ON/OFFAUX 1AUX 2AUX 3 - ° ~ +10dB PRE/POST MUTESOLO CH1 EFF - ° ~ +10dB 1 2 - ° ~ +10dB ST BUS ON/OFF 3 4 1 2 3 4GROUP1-2 ON/OFFMUTE 1 2 3 4GROUP3-4 ON/OFFCH16 EFFPRE/POST AUX 1AUX 2AUX 3 - ° ~ +10dB SOLO EQH: 12kHzM: 100-8kHzL: 80HzLINE1: -40 ~ -15dBu (37.8 ~ -12.8dBV) INPUT+/-18dBINPUTEQH: 12kHzMIC1: -60 ~ -35dBuTRIM M: 100-8kHzL: 80Hz+/-18dB A/D TIP: SENDRING: RETURNINSERT 2 1 PEAK (LIMITER)BABAL Low Cut Filter80Hz, -12dB/octMIC2: -37 ~ -12dBuLINE1: -40 ~ -15dBu (37.8 ~ -12.8dBV) LINE2: -17 ~ +8dBu (-14.8 ~ +10.2dBV) GAIN1: +28dBGAIN2: +5dB++P48 (1-8) MICLINE P48 (9-16) MICLINE BAL ++ TRIMBA A/D2 1 PEAK Low Cut Filter80Hz, -12dB/oct (LIMITER) A+48V P48V (1-8) P48V (9-16) ON/OFFON/OFFINPUT 1~8INPUT 15~16SUB IN EFF RTN 1-2EFF RTN 3-4EFF RTN AUX1EFF RTN AUX2EFF RTN AUX3 TO STTO STTO STST OUT LST OUT R OUTPUT LIMITERON/OFF SUB INSUB IN VOL IC VOL IC INPUT/SUB IN SUB IN CH1-8 FADER CH15-16 FADER CH1 PAN CH16 PAN ST BUS ON/OFF ATT: -20dBATT: -20dB LIMITER LIMITER LR INTERNALEFFECT ON/OFF 1 2 - ° ~ +10dB 3 4 1 2 3 4GROUP1-2 ON/OFFMUTE 1 2 3 4GROUP3-4 ON/OFFCH16 EFFPRE/POST AUX 1AUX 2AUX 3 - ° ~ +10dB SOLO EQH: 12kHzM: 100-8kHzL: ...
)
