Votos - 5, Puntuación media: 3.4
(
)
)
|
Resumen del manual
• Magnetic Shield Enclosure for Desktop Operation. • Deep and Rich Natural LF Sound. • Perfectly Matched Dual Power Amp (60W LF and 30W HF) for each Drivers. • Low Frequency Ports delivering Amazing Bass response. Supplied accessories In addition to this manual, the VL-X5 has been packed with the following: • Power cord • Warranty document Should any of these items be missing, or if you encounter any damage, please contact your TASCAM supplier. This unit was packed in its carton with special materials in order to prevent any damage during shipment. Please save the carton and packing materials in the event you need to transport the unit in the future. Environmental precausions The VL-X5 may be used in most places, but to maintain top performance and prolong operating life, do not place it in the following locations. • On an unsteady surface, or where there is frequent vibration or resonance • Near a window or where it can be exposed to direct sunlight • Near heating or air conditioning vents, or in very hot or cold places • Places with high humidity or poor ventilation • Next to tuners, televisions or video decks, as this could cause noise or affect video images TASCAM VL-X5 Owner's Manual Installation Installation 1 Precautions Handling Do not grab the speaker driver unit : the VL-X5 is packaged in box fitted tight, so your attention is required when taking speakers out of the box. To avoid the possible damage to the speaker units, hold both sides of the speaker to pull it out of the box. The units should not be touched to avoid damage even after it is out of the box. Recommend to use high quality balanced or unbalanced cable for input connection. Turn off the power of the VL-X5 and turn the Volume control of the VL-X5 to minimum before kaming the connection. Connection Connect XLR balanced or TRS balanced/unbalanced input of the VL-X5 to the output terminal of the audio equipment. 2 Connection Assure that the power switch of VL-X5 is turned off and volume control of VL-X5 is turned to minimum. Connect male side of XLR balanced cable, TRS balanced cable, or TS unbalanced cable to the input connector of the VLX5. XLR Balanced Cable XLR / TRS Combo Jack Power Cord TRS Balanced or Unbalanced Cable Power Cord XLR PIN 1: GND PIN 2: HOT PIN 3: COLD TRS Tip: HOT Ring: COLD Sleeve: GND 3 Connecting to the audio equipment Before connecting, make sure its power is turned off. Plug the XLR balanced, TRS balanced or TS unbalanced cable to the corresponding output connectors of the audio equipment. Pre-Amplifier, Sound card, Mixer Output VL-X5 VL-X5 6 TASCAM VL-X5 Owner's Manual Placing the VL-X5 Placing the VL-X5 Placing the speakers is one of the most important procedures to monitor correct sound. To monitor with VL-X5 at its maximum capability, appropriate listening environment and correct placement are required. Please, refer to the following to place the VL-X5 correctly. 1 VL-X5's set up position is 60 cm (Recommendation 100 cm) to the back and 40cm (Recommendation 60 cm) to the side. 2 Basically, two units and the listener should align to from a regular triangle. 3 The height of units, more precisely, the top of the woofer should come up to where your ears are in normal listening environment. 4 Recommend Place the VL-X5 horizontally. If you Placing VL-X5 horizontally, refer to the following diagram. 60 cm 40 cm Left Right NOTE DO NOT place any obstacles that may block the flow of air, which is medium of the sound, or create reflected sound, especially, the material of high reflection tendency including glass, mirror or metal. Place those materials away from the path of the sound from VL-X5. TASCAM VL-X5 Owner's Manual 7 Rear panel Rear panel 7 8 9 1 2 3 4 5 6 1 XLR INPUT This jack accept XLR input connection, wire either balanced or unbalanced. The signal of XLR INPUT is summed together with TRS INPUT through a balanced input amplifier. So, either may be used as an input or mixed together. Input specifications apply to both inputs. The INPUT CONNECTIONS wiring chart of XLR connector is following: Pin 1: GND Pin 2: HOT Pin 3: COLD 2 TRS INPUT This jack accepts a TRS connector, wire either balanced or unbalanced. For balanced wiring, a 3-conductor TRS plug is necessary. The INPUT CONNECTIONS wiring chart of TRS connector is as following: Tip: HOT (+) Ring: COLD (-) Sleeve: GND Unbalanced wiring works with either a 2 or 3-conductor TRS connector. A 2-conductor TRS plug automatically ground the minus signal input, whereas a 3-conductor TRS plug wired unbalanced provides the option of leaving the minus open or grounded. We recommend that you grounded the unused input. The TRS INPUT is summed together with XLR INPUT through a balanced Input amplifier. So, either may be used as an input or mixed together. Input specifications apply to both inputs. 3 VOLUME Control < MIN > < MAX > Use the Volume Control to set the output sound pressure from VL-X5 to proper level required. 4 POWER LED When power of VL-X5 is on, the LED wil...