Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
2. Cycle the key by turning the ignition on then back off, then back on again to test the radio for proper operation. 3. If the subwoofer or front door speakers are too loud you can adjust the output by following the steps below: A. Locate the end of the MITO-01 with the 14 way Molex connector. B. There are 2 potentiometers next to the Molex connector, the one closest to the Molex connector is the subwoofer control and the other one is the front door speaker control. 1-800-221-0932 ©Copyright 2010 Metra Electronics Corporation ©Copyright 2010 Metra Electronics Corporation SUBWOOFER CONTROLFRONT DOOR SPEAKERCONTROL C. Using a small blade screwdriver turn the potentiometer of the speaker you want to adjust either clockwise to make it louder or counterclockwise to lower the volume. 5 MITO-01 INSTALLATION INSTRUCTIONS INTERFACE COMPONENTS • MITO-01 Interface • 14 Pin Harness with RCA’s • Vehicle side harness • 2 Pin harness * READ IMPORTANT WARNING ON PAGE 2 BEFORE ATTEMPTING ANY INSTALLATION The MITO-01is designed to be used in vehicles listed in the applications that have the Rockford Fosgate audio sys- tem.The Rockford Fosgate system uses a digital signal to turn on the amplifier. The MITO-01 supplies that digital sig- nal to turn the amplifier on and also eliminates the “COM ERROR” message on the display when the OEM radio is removed. When installing a radio that has navigation built in, the MITO-01 can supply VSS (Vehicle Speed Sense), Parking Brake, and Reverse; however Reverse is not avail- able on manual transmission vehicles. The radios speaker wires will provide the audio for the dash and rear speakers while the rca’s will provide the audio to the amplifier to power the door speakers and woofer. 1-800-221-0932 KNOWLEDGE IS POWEREnhanceyour installation and fabrication skillsbyenrolling in the most recognizedandrespectedmobile electronics school in our industry. Log onto for more informationandtake stepstoward abetter tomorrow. Rev. 03/11/10 INSTMITO-01 MITO-01 TOOLS REQUIRED FOR INSTALLATION • Cutting Tool • Small Blade Screwdriver • Tape • Crimping Tool • Connectors (I.E. butt-connectors, bell caps, etc…) APPLICATIONS MITSUBISHI Eclipse 2006-2010 MITSUBISHI Endeavor 2007-2009 * IMPORTANT WARNING THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE CAREFULLY FOLLOWED. THE INSTRUCTIONS ARE WORDED IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COMPLETING THESE TYPE OF ELECTRONIC INSTALLATIONS. IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT A TECHNICIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING. FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE. INTERFERENCE WITH CERTAIN SAFETY SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL. IF YOU HAVE ANY QUESTIONS IN THIS REGARD PLEASE CALL THE HELP LINE OR THE METRA AT 1-800-221-0932 FOR ASSISTANCE. BEFORE WIRING UP THE MITO-01 *Important: Before beginning any of the following, disconnect the negative battery terminal to prevent an accidental short circuit. WIRING CONNECTIONS TO BE MADE ON THE VEHICLE SIDE HARNESSES: 1. Connect the Yellow wire to the radio’s 12 volt battery or memory wire. 2. Connect the Red wire to the radios 12 volt ignition or accessory wire. 3. Connect the Black wire with the fork connector to a good ground, like a metal brace in the dash. 4. Connect the Black wire to the radios ground wire. 5. Connect the Orange wire to the radios Illumination wire. If the radio does not have an Illumination wire just tape up the wire. 6. Connect the Blue wire to the radios power antenna turn on wire. 7. Connect the White wire to the radios Left Front (+) speaker wire. 8. Connect the White/Black wire to the radios Left Front (-) speaker wire. 9. Connect the Gray wire to the radios Right Front (+) speaker wire. 10. Connect the Gray/Black wire to the radios Right Front (-) speaker wire. 11. Connect the Green wire to the radios Left Rear (+) speaker wire. 12. Connect the Green/Black wire to the radios Left Rear (-) speaker wire. 13. Connect the Purple wire to the radios Right Rear (+) speaker wire. 14. Connect the Purple/Black wire to the radios Right Rear (-) speaker wire. If the radio you are installing has navigation built in, the MITO-01 can supply the necessary navigation outputs with some additional wiring. The MITO-01 comes with a 2 pin connector with a Pink and a Blue/Pink wire in it. Follow the steps below to connect these wires to the vehicle: 1. Connect the 2 pin connector with loose leads to the mating connector on the vehicle side harness of the MITO-01. 2. Locate the OBD2 connector which is located beneath the driver’s side dash panel close to the center console and run the Pink and the Blue/P...