Votos - 6, Puntuación media: 4.3 ( )

Fabricar: Marshall Amplification Tamaño del archivo: 340.01 kb Nombre del archivo: Idioma del manual:

These can then be recalled when using the unit in Preset mode. When channel settings have been stored the current channel light (3 or 5) will stop flashing indicating the preset has been saved. Reverb & FX The amplifier provides three simultaneous effects, Reverb, Delay and one of three Modulation effects (Chorus, Phaser, orFlanger). Reverb The Reverb control sets the amount of signal sent to the reverb section - allowing the reverb to spill between channels as different presets are recalled. The Rev switch (8) switches the reverb effect on and off, the status of the reverb is also indicated on the footcontroller. FX The FX section consists of two effects, Delay and Modulation. The FX section can be globally turned on and off via the FX switch (11). Delay The Delay control (14) sets the amount of signal sent to the delay section. When the Delay control (14) is set to ‘0’ the delay is switched off. Modulation The Mod control (12) is split into three segments and selects the type of modulation effects and adjusts its associated settings. When the Mod control (12) is set to ‘0’ the modulation effects are switched off. 0 Modulation Off Chorus Speed increases and depth is reduced as knob is turned clockwise. Phaser Speed increases as knob is turned clockwise. Flanger Speed increases, feedback and depth are reduced as knob is turned clockwise. Tap Tempo The Tap Tempo switch (13) is used for the Delay effect only. The Tap Tempo switch matches the delay time to the time between two presses. The Tap Tempo LED flashes red at the selected/recalled delay time. The number of repeats is reduced as the delay time decreases. If you change from a channel with delay to one without delay the effect will spill between channels. If you change from a channel with delay to a channel with delay set to a different delay time the delay effect will not spill between channels. MP31 Line In The 3.5mm MP3 / Line In socket (24) on the rear panel allows the connection of an external audio source e.g. MP3 or CD player. 6 Headphones & Line Out The 3.5mm Headphones socket (18) allows the connection of a pair of headphones. When a jack is inserted into the headphones socket the unit’s speaker is muted. Additionally the Headphones socket (18) can also be used as a Line Out to send the signal to an external equipment e.g. A computer, digital recorder or mixer. When a jack is inserted into the socket the unit’s speaker is muted providing ‘silent recording’. The unit’s output can then be monitored directly from the external equipment used. Damping The Damping switch (17) selects between the two modes of power amp damping. When Damping is off (LED off), the power amp response resembles the feel of a classic power amp with emphasized middle and limited bass and treble. Switching Damping on (LED on) will boost the speaker resonances both in the bass and high frequency ranges. FX Loop The FX Return socket (25) on the rear panel is used to connect the OUTPUT of the effects processor or pedal you are using in the effects loop. The FX loop is series and set at instrument level so both guitar FX or professional units can be connected. The FX Send socket (26) on the rear panel is used to connect to the INPUT of the unit you are using in the effects loop. The FX loop is switched on and off via the Ext FX switch (15) on the front panel. Loudspeaker ALWAYS USE ANON-SCREENED MARSHALL APPROVED SPEAKER LEAD WHEN CONNECTING AN EXTENSION CABINET TO THESE AMPLIFIERS. MG50FX The single Loudspeaker socket (22) is used to connect either the internal speaker or an external speaker cabinet to the unit’s power amp. When using external cabinets ensure the total load impedance is equal to, or exceeds, 8 ohms. MG100FX 1x12" & 2x12" Combos The single Loudspeaker socket (22) is used to connect either the internal speaker or an external speaker cabinet to the unit’s power amp. When using external cabinets ensure the total load impedance is equal to, or exceeds, 4 ohms. MG100HFX Head The two Loudspeaker sockets are used to connect to 1 or 2 external cabinets. When using external cabinets ensure the total load impedance is equal to, or exceeds, 4 ohms. Power The Power switch (20) turns the amplifier on and off. If current settings have not been stored they will be lost. Restoring Settings - WARNING: ALL AMP & FOOTSWITCH SETTINGS WILL BE LOST To restore the unit to factory settings (see handbook rear cover) you must hold the Store switch (19) while powering on the amplifier. The Clean/Crunch (3) and OD (5) lights will light orange. You can then release the Store switch (19). Resetting the amplifier will erase all user Channel presets and all user Footcontroller settings, replacing them with the factory presets. * EUROPE ONLY V V - Note: This equipment has been tested and found to comply with the requirements of the EMC Directive (Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E.U. * EUROPE ONLY - No...

Descargar ahora

Introduzca dos números de la imagen: