Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
TheXLRoutputsarewiredasfollows: Pin 1 = Shield or ground Pin 2 = Positive (+ or hot) Pin 3 = Negative (– or cold) Like the inputs, the routing for the 32 returns on the DS3232 is configured by the mixing console. Generally, this will be done in the Setup window for the expansion cards where the U100 Network card is installed. In the case of the TT24, there is no configuration required for the returns. Rear Panel All the connection points (other than the power cord) are located on the front panel for easy accessibility when rack mounted. 6. POWER Switch This one is self-explanatory. When the POWER switch is turned ON, power is supplied to the DS3232 and the POWER LED on the front panel lights up. Press the bottom of this switch to put the DS3232 into standby mode. It will not function, but the circuits are still live. To remove AC power, either turn off the AC mains supply, or unplug the power cord from the DS3232 and the AC mains supply. 7. POWER Receptacle This is a standard 3-prong IEC power connector. Connect the detachable linecord (included in the box with your DS3232) to the power receptacle, and plug the other end of the linecord into an AC outlet. The DS3232 has a universal power supply that can accept any AC voltage ranging from 100 VAC to 240 VAC. No need for voltage select switches. It will work virtually anywhere in the world. That’s why we call it a “Planet-Earth” power supply! This also means that it is less susceptible to voltage sags or spikes, providing greater electromagnetic isolation and better protection against AC line noise. 8. Fan The DS3232 is fan-cooled and brings air in through the sides and out through the rear. Make sure that cool air is available at the sides of the unit, and that there is room at the rear for the warm air to exit from the enclosure and dissipate. If rack-mounted, make sure the DS3232 is not pulling warm (or hot) air in from the rack, and that the sides and rear are not obstructed. SERIAL NUMBER MANUFACTURING DATE RISK OF ELECTRIC SHOCK DO NOT OPEN REPLACE WITH THE SAME TYPE FUSE AND RATING. DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR CAUTION: POWER DS3232 24-BIT / 96kHz DIGITAL SNAKE Appendix A: Service Information If you think your Mackie product has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website (where you will find lots of useful information such as FAQs, documentation, and user forums. You may find the answer to the problem without having to send your Mackie product away. Troubleshooting No Power • Our favorite question: Is it plugged in? • Make sure the power cord is securely seated in the IEC socket [7] and plugged all the way into the AC outlet. • Make sure the AC outlet is live (check with a tester or lamp). • Is the POWER [6] switch on? Make sure the POWER switch on the rear panel is in the ON position (up). • Is the POWER LED [2] on the front panel illuminated? If not, make sure the AC outlet is live. • Are all the lights out in your building? If so, contact your local power company to get power restored. • If the POWER LED is not illuminated, and you are certain that the AC outlet is live, it will be necessary to have your DS3232 serviced. There are no user serviceable parts inside. Refer to “Repair” at the end of this section to find out how to proceed. No COMM Indication • Are the power switches on the mixer and the DS3232 turned on? • Verify that the Cat5e cable is working properly. Replace with a known working cable, if possible. • Does the Snake appear in the Expansion Slot Setup Screen? If not, check to see that the U100 card is properly seated in the expansion slot. • Try putting the U100 card in another slot (be sure to turn everything off before removing and replacing the card). • Is the fan running and unobstructed so it can circulate air through the DS3232? If the DS3232 feels hot to the touch, power off the unit for a few minutes to allow it to cool. Turn the unit back on and, if communication is restored, provide better ventilation so cool air is available to the DS3232. No Input • Is the mixing console properly configured to accept the input signals from the DS3232? Make sure the inputs for the mixing console have been setup to accept the 32 input signals from the DS3232. • Is the input GAIN control for the channel turned up on the mixing console? • Is the fader turned up? • Is the signal source turned up? Make sure the signal level from the selected input source is high enough to light up some of the INPUT meter LEDs. • Try the same source signal in another channel, set up exactly like the suspect channel. No Output • Is the associated level control (if any) turned up? •...