Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
• Musician Made in the U.S.A. BV-60H / BV-120H All Tube Guitar Amplifiers CHANNEL CHANNELCHANNEL EFFECTS LOOP EFFECTS LOOPEFFECTS LOOP OOO 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 SELECT SELECTSELECT PAD (12dB) AD (12dB)AD (12dB) 2 5 84 6 3 7 OFF OFFOFF 2 1 1 9 O 1O O 1O O 1O O 1O -5 +5 -5 +5 -5 +5 O 1O EFFECTS LOOP EFFECTS LOOPEFFECTS LOOPONON POWER STANDBY PRESENCE LEVEL LEVEL VOLUME LOW MID HIGH GAIN 21 CHANNEL 1CHANNEL 2REVERB 1 2 345 6 7 8 9 10111213 The Front Panel: Channel 2: 1. POWER (not shown): This switch applies 8. MASTER: Set the output signal level of AC voltage to the amplifier, and should always channel 2 with this control. At the "0" position be turned on first. The switch illuminates when (full left) very little or no signal will be heard; as the AC power is on. you rotate the control clockwise (towards center) the output level of channel 2 increases. Use 2. STANDBY (not shown): This switch actithis control along with your guitar's volume and vates the amplifier, and should always be turned the channel 2 gain control (#12) to produce a on last. The switch illuminates when the high wide variety of sounds. voltage power is passing through to the tubes. 9. LOW: Adjust the bottom end response with NOTE: When you first power up this this control. The low control covers a range of amplifier, leave the Standby switch OFF 15dB at 100Hz. This sets the amount of bass for at least 20 seconds. This gives the heard (and felt) from the amp. power tubes a chance to prepare themselves for action. 10. MID: Adjust the midrange response with this control. The mid control covers a range of 13dB 3. PRESENCE: Increase the level of upper harat 500Hz. This controls the “voice” of your guitar. monics with this control. The presence control allows a boost of up to 5dB at 10kHz. 11. HIGH: Adjust the high end response with this control. The high control covers a range of 4. EFFECTS LOOP PAD: This switch activates 10dB at 10kHz. This controls the “bite” of your a 12dB pad on the effects send signal and cor guitar. responding gain recovery on the return. In the out position the signal is full strength which is 12. GAIN: Adjust the overdrive (distortion) level best suited for line level rack mountable effects. with this control. With the control towards “0” (to With the switch depressed the signal is lower the left) the signal is relatively clean. As you which is best suited for foot pedal type effects. rotate the control clockwise the distortion increases, along with the overall output level. 5. EFFECTS LOOP SWITCH: This switch con- Rotate the control towards “10” and you’ll trols the effects return signal of the effects loop. increase the distortion even more. The loop is only active when the switch is pressed in. When a footswitch is used, this 13. CHANNEL SELECT: Switch between chanswitch is disabled. The adjacent yellow LED illu-nels with this push-button switch. The adjacent minates when the loop is in use. amber LED illuminates when channel 1 is selected (switch in the out position), the red 6,7. REVERB 2, REVERB 1: Adjust the amount LED illuminates when channel 2 is selected of reverberation on each channel with these (switch depressed). When a footswitch is used controls: at the "0" position the signal is "dry" for channel switching, this switch is disabled. (no reverb). As you rotate the control clockwise, the amount of reverb increases. OOO 234 56781 9 -5 +5 -5 +5 -5 +5 O 1O LOW MID HIGH VOLUME INPUT 14151617 18 Channel 1: 14. LOW: Adjust the bottom end response with this control. The low control covers a range of 16dB at 100Hz. This sets the amount of bass heard (and felt) from the amp. 15. MID: Adjust the midrange response with this control. The mid control covers a range of 20dB at 300Hz. This controls the “voice” of your guitar. 16. HIGH: Adjust the high end response with this control. The high control covers a range of 10dB at 10kHz. This controls the “bite” of your guitar. 17. VOLUME: Set the output volume level of channel 1 with this control. 18. INPUT: Connect your guitar or wireless receiver into this standard 1/4" jack by means of a shielded instrument cable. BV-60H / BV-120H All Tube Guitar Amplifiers SPEAKERS IMPEDANCE 100 WATTS RMS SELECTOR 816 MAIN EXT. LINE OUT (USE FIRST) 19 2021 22 The Rear Panel: 19. IMPEDANCE SELECTOR: For the best performance and least strain on your amplifier, you MUST properly match the impedance of your amplifier to that of your speaker cabinet(s). Set the selector switch to the 8 or 16 ohm position, depending on the total impedance of your speaker cabinet(s). The chart below can help you determine that impedance based on the following combinations of speakers connected in parallel. CAB. IMP. # OF CABS. TOTAL IMP. 8 OHMS 1 8 OHMS 16 OHMS 1 16 OHMS 16 OHMS 2 8 OHMS 32 OHMS 2 16 OHMS 32 OHMS 4 8 OHMS 20. MAIN SPEAKER JACK: Use this jack to connect the amplifier to your primary speaker cabinet by means of a heavy gauge speaker cable. Always k...
Otros modelos de este manual:Instrumentos Musicales - ALL TUBE BV-60H (345.66 kb)