Votos - 2, Puntuación media: 4 ( )

Fabricar: PYLE Audio Tamaño del archivo: 3.88 mb Nombre del archivo: Idioma del manual:

Please note that Phone 1 and Line 1 (as well as Phono 2 and Line 3) use the same jacks. The selector switch below the jacks should be set to Phono position if the jacks are used for phono inputs. When using a turntable, you should also securely connect its ground wire (usually green or black) to the Ground screw on the input panel of the mixer. NOTE! If you use a Turntable in the Phonol/Linel (and/or Phono2/Une3) input jack(s), be sure to place the Input Select switch in the PHONOl (and/or PH0N02) position(s)! Use RCA type patch cables GROUND wire from turntable Magnetic cartridge turntable _ ^-i. LEFT output RIGHT output Pyle Pro Mixer Owner's Manual - 7 Using the Channel Input Gain Controls Adjusting the Gain controls for each channel permits you to fíne tune the level of each of the audio inputs, since input levels usually vaiy. Rotate the Gain controls clockwise to increase levels. After you preset the gain levels for each input, it is recommended that you do not adjust them further, as you can cause sound level imbalances during a mix. Connecting the Mixer Outputs Output to an Amplifier To play the mixer's output signal through your speaker system (for events such as parties, dances, conferences, etc.) connect an audio patch cord (not supplied) from the mixers AMP L and R jacks to your receiver amplifier's left and right input jacks. This mixer features two kinds of output jacks for you to choose from: RCA style and 1/4" type. DO NOT USE BOTH SIMULTANEOUSLY. Output to a Tape or Digital Audio Recorder To play the mixer's output signal through your speaker system (for events such as parties, dances, conferences, etc.) connect an audio patch cord (not supplied) from the mixers REC L and R jacks to your receiver/amplifier's left and right input jacks. Zone Output To monitor the mixer output to a second set of speakers in the DJ booth (or in a remote location) connect an audio patch cord (not supplied) from the mixers ZONE L and R jacks to your secondary amplifier's left ana right input jacks. CAUTION: In order to avoid sudden unpleasant sound output, adjust the output devices controls to these settings before you connect the mixer's output jacks to these devices' input jacks. OUTPUT DEVICE CONTROL SETTING Tape Deck POWER OFF Amplifier/Receiver POWER OFF TONE FLAT 8 - Pyle Pro Mixer Owner's Manual Using Headphones Do not listen at extremely high volume levels. Extended, high-volume listening can lead to permanent hearing loss. Follow these guidelines to protect your hearing, especially when using headphones. Always start by setting the volume level to the lowest possible level before listening. Put headphones on, and then gradually increase the volume as necessary. Once you set the volume level do not increase it. Over a period of time, your ears adapt to a volume level and there is a temptation to increase it. Even though such an increase may not cause discomfort, it might still damage your hearing. Plug a pair of stereo headphones (not supplied) with a 1/4" jack into the Phones input. Using headphones not only affords you the opportunity to listen privately, but also enables you to monitor ("cue") the incoming audio sources so you can locate an exact passage or section before mixing it in. It also gives you the opportunity to set up the relative volume level of the upcoming passage before it joins the mix. Listen Safely! Please observe the following: Stereo Headphones Connecting the Lamp If you wish to intall a console lamp (not supplied), simply insert the plug end of an appropriate 12V/3W gooseneck style or similar lamp into the lamp socket provided in the upper right corner of the mixer control panel. Power is supplied to this lamp when the mixer power switch is turned on. 12V/3W lamp Pyle Pro Mixer Owner's Manual - 9 Using the Mixer Controls Turning on the Mixer 1. Turn on the output amplifier and temporarily set its volume to the minimum setting. 2. On the mixer, turn ON the power switch. The adjacent power LED will illuminate. 3. Turn on the audio input sources you wish to mix, and set them to play (or talk continuously into the microphone). 4. To monitor the audio input sources so that you can decide when to mix in each input, see "Monitoring 'Cueing'the Inputs." 5. To mix the audio input sources so that you can play them through your amplifier system or record them on your tape deck, see "Mixing the Inputs." Monitoring ("Cueing") the Inputs 1. Set the CUE ASSIGN switch of the input source (MIC, CHI, CH2, CH3 or CH 4) you wish to monitor. 2. Adjust the Headphone Level control to a comfortable listening level. 3. The Headphone CUE/PGM control permits you to switch easily from listening to CUE material to the playing PROGRAM sound. You can also listen to both simultaneously by moving the Headphone CUE/PGM control to a point midway between the two ends. PYD-1939 and PYD-1949: These models also have an F/X CUE for you to monitor the sound effect be...

Descargar ahora

Introduzca dos números de la imagen: